ATTINY25-15MZ Atmel, ATTINY25-15MZ Datasheet - Page 151

• Manufacturer Part Number: ATTINY25-15MZ
• Description: MCU AVR 2K FLASH 15MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY25-15MZ

• Package / Case: 20-QFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 6
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: UART, SPI, USI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Data Rom Size: 128 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 4
• Height: 0.75 mm
• Length: 4 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 22-1.
Notes:
22.2
Figure 22-1. External Clock Drive Waveforms
7598H–AVR–07/09
Symbol
I
CC
(6)
1. All DC Characteristics contained in this data sheet result from actual silicon characterization.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (8 mA at V
5. Although each I/O port can source more than the test conditions (8 mA at V
6. All I/O modules are turned off (PRR = 0xFF) for all I
7. Brown-Out Detection (BOD) disabled.
External Clock Drive Waveforms
ditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Power Supply Current
Power-down mode
DC Characteristics T
(7)
V
IL1
V
IH1
A
= -40°C to 125°C, V
Active 4MHz, V
Active 8MHz, V
Active 16MHz, V
Idle 4MHz, V
Idle 8MHz, V
Idle 16MHz, V
WDT enabled, V
WDT disabled, V
WDT enabled, V
WDT disabled, V
Condition
CC
CC
CC
CC
CC
= 3V
= 5V
CC
CC
CC
CC
CC
= 5V
= 3V
= 5V
= 3V
= 5V
= 5V
= 3V
= 5V
CC
CC
= 2.7V to 5.5V (unless otherwise noted)
values.
Min.
(2)
CC
= 5V, 5 mA at V
CC
= 5V, 5 mA at V
Typ.
1.25
0.4
1.2
2.5
10
5
5
2
9
3
CC
ATtiny25/45/85
= 3V) under steady state con-
CC
Max.
0.5
= 3V) under steady state
10
15
30
24
50
36
3
2
5
(1)
(3)
.
Units
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
151