ATMEGA329P-20MN Atmel, ATMEGA329P-20MN Datasheet - Page 331

• Manufacturer Part Number: ATMEGA329P-20MN
• Description: IC MCU AVR 32K 20MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA329P-20MN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 28-1.
Notes:
8021G–AVR–03/11
Symbol
V
I
t
ACLK
ACID
ACIO
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min.” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at V
4. Although each I/O port can source more than the test conditions (20mA at V
V
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100mA.
If IOL exceeds the test condition, VOLmAy exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
at V
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
T
CC
= 5V, 5mA at V
A
= 5V, 5mA at V
= -40°C to 85°C, V
CC
CC
= 3V for all other ports) under steady state conditions (non-transient), the following must be observed:
= 3V for all other ports) under steady state conditions (non-transient), the following must be
CC
V
V
V
Condition
V
V
V
= 1.8V to 5.5V (unless otherwise noted) (Continued)
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
Min.
-50
CC
= 5V, 10mA at V
CC
= 5V, 10mA at V
Typ.
<10
750
500
ATmega329P/3290P
CC
CC
= 3V for Port B and 10mA at
Max.
40
50
= 3V for Port B and 10mA
Units
mV
nA
ns
331