ATMEGA329P-20MN Atmel, ATMEGA329P-20MN Datasheet - Page 54

• Manufacturer Part Number: ATMEGA329P-20MN
• Description: IC MCU AVR 32K 20MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA329P-20MN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8021G–AVR–03/11
Table 11-2
BOOTRST and IVSEL settings. If the program never enables an interrupt source, the Interrupt
Vectors are not used, and regular program code can be placed at these locations. This is also
the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the
Boot section or vice versa.
Table 11-2.
Note:
The most typical and general program setup for the Reset and Interrupt Vector Addresses in
ATmega329P/3290P is:
BOOTRST
Address
0x0000
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
0x0012
0x0014
0x0016
0X0018
0x001A
0x001C
0x001E
0x0020
0x0022
0x0024
0x0026
0x0028
0x002A
0x002C
0x002E
0x0030
;
0x0032
0x0033
1
1
0
0
2. When the IVSEL bit in MCUCR is set, Interrupt Vectors will be moved to the start of the Boot
3. PCINT2 and PCINT3 are only present in ATmega3290P.
1. The Boot Reset Address is shown in
Flash Section. The address of each Interrupt Vector will then be the address in this table
added to the start address of the Boot Flash Section.
means unprogrammed while “0” means programmed.
shows reset and Interrupt Vectors placement for the various combinations of
Reset and Interrupt Vectors Placement
Labels
RESET:
IVSEL
0
1
0
1
Code
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
ldi
out
Reset Address
0x0000
0x0000
Boot Reset Address
Boot Reset Address
RESET
EXT_INT0
PCINT0
PCINT1
TIM2_COMP
TIM2_OVF
TIM1_CAPT
TIM1_COMPA
TIM1_COMPB
TIM1_OVF
TIM0_COMP
TIM0_OVF
SPI_STC
USART_RXC
USART_UDRE
USART_TXC
USI_STRT
USI_OVF
ANA_COMP
ADC
EE_RDY
SPM_RDY
LCD_SOF
PCINT2
PCINT3
r16, high(RAMEND)
SPH,r16
Table 26-6 on page
(1)
Interrupt Vectors Start Address
0x0002
Boot Reset Address + 0x0002
0x0002
Boot Reset Address + 0x0002
ATmega329P/3290P
Comments
; Reset Handler
; IRQ0 Handler
; PCINT0 Handler
; PCINT1 Handler
; Timer2 Compare Handler
; Timer2 Overflow Handler
; Timer1 Capture Handler
; Timer1 CompareA Handler
; Timer1 CompareB Handler
; Timer1 Overflow Handler
; Timer0 Compare Handler
; Timer0 Overflow Handler
; SPI Transfer Complete Handler
; USART0 RX Complete Handler
; USART0,UDR0 Empty Handler
; USART0 TX Complete Handler
; USI Start Condition Handler
; USI Overflow Handler
; Analog Comparator Handler
; ADC Conversion Complete Handler
; EEPROM Ready Handler
; SPM Ready Handler
; LCD Start of Frame Handler
; PCINT2 Handler
; PCINT3 Handler
; Main program start
; Set Stack Pointer to top of RAM
292. For the BOOTRST Fuse “1”
54