ADUC831BS Analog Devices Inc, ADUC831BS Datasheet - Page 53

• Manufacturer Part Number: ADUC831BS
• Description: IC ADC/DAC 12BIT W/MCU 52-MQFP
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC8xxr

Specifications of ADUC831BS

• Rohs Status: RoHS non-compliant
• Core Processor: 8052
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: PSM, Temp Sensor, WDT
• Number Of I /o: 34
• Program Memory Size: 62KB (62K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 52-MQFP, 52-PQFP
• For Use With: EVAL-ADUC831QSZ - KIT DEV FOR ADUC831 QUICK START

T2CON
SFR Address
Power-On Default Value
Bit Addressable
Bit
6
5
4
3
2
1
0
Timer/Counter 2 Data Registers
Timer/Counter 2 also has two pairs of 8-bit data registers
associated with it. These are used as both timer data registers
and timer capture/reload registers.
TH2 and TL2
Timer 2, data high byte and low byte.
SFR Address = CDH, CCH respectively.
RCAP2H and RCAP2L
Timer 2, Capture/Reload byte and low byte.
SFR Address = CBH, CAH respectively.
REV. 0
7
Name
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
CNT2
CAP2
Timer/Counter 2 Control Register
C8H
00H
Yes
Description
Timer 2 Overflow Flag.
Set by hardware on a Timer 2 overflow. TF2 will not be set when either RCLK = 1 or TCLK = 1.
Cleared by user software.
Timer 2 External Flag.
Set by hardware when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.
Cleared by user software.
Receive Clock Enable Bit.
Set by user to enable the serial port to use Timer 2 overflow pulses for its receive clock in serial port
Modes 1 and 3.
Cleared by user to enable Timer 1 overflow to be used for the receive clock.
Transmit Clock Enable Bit.
Set by user to enable the serial port to use Timer 2 overflow pulses for its transmit clock in serial port
Modes 1 and 3.
Cleared by user to enable Timer 1 overflow to be used for the transmit clock.
Timer 2 External Enable Flag.
Set by user to enable a capture or reload to occur as a result of a negative transition on T2EX if
Timer 2 is not being used to clock the serial port.
Cleared by user for Timer 2 to ignore events at T2EX.
Timer 2 Start/Stop Control Bit.
Set by user to start Timer 2.
Cleared by user to stop Timer 2.
Timer 2 Timer or Counter Function Select Bit.
Set by user to select counter function (input from external T2 pin).
Cleared by user to select timer function (input from on-chip core clock).
Timer 2 Capture/Reload Select Bit.
Set by user to enable captures on negative transitions at T2EX if EXEN2 = 1.
Cleared by user to enable auto-reloads with Timer 2 overflows or negative transitions at T2EX
when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to
autoreload on Timer 2 overflow.
Table XXI. T2CON SFR Bit Designations
–53–
ADuC831