HD6417020SVX12I Renesas Electronics America, HD6417020SVX12I Datasheet - Page 412

• Manufacturer Part Number: HD6417020SVX12I
• Description: IC SUPERH MPU ROMLESS 100TQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7020r

Specifications of HD6417020SVX12I

• Core Processor: SH-1
• Core Size: 32-Bit
• Speed: 12.5MHz
• Connectivity: EBI/EMI, SCI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

Table 13.13 SSR Status Flags and Transfer of Receive Data
Receive Error Status
Overrun error
Framing error
Parity error
Overrun error + framing error
Overrun error + parity error
Framing error + parity error
Overrun error + framing error + parity
error
O:
X:
Break Detection and Processing: Break signals can be detected by reading the RxD pin directly
when a framing error (FER) is detected. In the break state, the input from the RxD pin consists of
all 0s, so FER is set and the parity error flag (PER) may also be set. In the break state, the SCI
receiver continues to operate, so if the FER bit is cleared to 0, it will be set to 1 again.
Sending a Break Signal: When TE is cleared to 0 the TxD pin becomes an I/O port, the level and
direction (input or output) of which are determined by the data register (DR) of the I/O port and
the control register (CR) of the PFC. This feature can be used to send a break signal. The DR
value substitutes for the mark state until the PFC setting is performed. The DR bits should
therefore be set as an output port that outputs 1 beforehand. To send a break signal during serial
transmission, clear the DR bit to 0, and select output port as the TxD pin function by the PFC.
When TE is cleared to 0, the transmitter is initialized, regardless of its current state.
Receive Error Flags and Transmitter Operation (clocked synchronous mode only): When a
receive error flag (ORER, PER, or FER) is set to 1, the SCI will not start transmitting even if
TDRE is set to 1. Be sure to clear the receive error flags to 0 before starting to transmit. Note that
clearing RE to 0 does not clear the receive error flags.
Receive Data Sampling Timing and Receive Margin in the Asynchronous Mode: In the
asynchronous mode, the SCI operates on a base clock of 16 times the bit rate frequency. In
receiving, the SCI synchronizes internally with the falling edge of the start bit, which it samples on
the base clock. Receive data is latched on the rising edge of the eighth base clock pulse. See figure
13.21.
Receive data is transferred from RSR–RDR.
Receive data is not transferred from RSR–RDR.
RDRF
1
0
0
1
1
0
1
SSR Status Flags
ORER
1
0
0
1
1
0
1
FER
0
1
0
1
0
1
1
PER
0
0
1
0
1
1
1
Receive Data
Transfer
RSR
X
O
O
X
X
O
X
RENESAS 395
RDR