RN-134-K Roving Networks Inc, RN-134-K Datasheet - Page 29

• Manufacturer Part Number: RN-134-K
• Description: KIT EVAL WIFLY GSX 802.11 RN-134
• Manufacturer: Roving Networks Inc
• Type: Transceiver, 802.11 b/gr

Specifications of RN-134-K

• Frequency: 2.4GHz
• Wireless Frequency: 2402 MHz to 2480 MHz
• Interface Type: RS-232, UART
• Modulation: CKK, DSSS, DBPSK, DQPSK, OFDM
• Security: 128 WEP, WPA, TKIP
• Operating Voltage: 3 V to 12 V
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: RN-134
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 740-1035

There are 2 timers that can be used to put the module to sleep, and perform a wake up. If the sleep timer is
There are 2 timers that can be used to put the module to sleep, and perform a wake up. If the sleep timer is
There are 2 timers that can be used to put the module to sleep, and perform a wake up. If the sleep timer is
enabled, the module will automatically go into deep sleep low power mode once the timer counts down to 0.
The sleep timer is disabled if the module has an IP connection, or the module is in COMMAND mode.
The sleep timer is disabled if the module has an IP connection, or the module is in COMMAND mode.
The sleep timer is disabled if the module has an IP connection, or the module is in COMMAND mode.
The sleep timer (which is the time the WiFly is awake) is a 32 bit number of s
The sleep timer (which is the time the WiFly is awake) is a 32 bit number of seconds so it can be as high as
1.19 million hours.
sleeping time is 1165 hours.
The sleep timer is set with : set sys sleep <time>
The wake timer will bring the module out of deep sleep.
The wake timer will bring the module out of deep sleep.
The wake timer is set with: set sys wake <time>
For example, if you wanted the module to wake up, join a network and be available to accept TCP
For example, if you wanted the module to wake up, join a network and be available to accept TCP
For example, if you wanted the module to wake up, join a network and be available to accept TCP
connections for 30 seconds every 2 minutes you would set the timers as such
The above diagram shows the transitions between the Sleep state and Awake state based on the sle
The above diagram shows the transitions between the Sleep state and Awake state based on the sle
The above diagram shows the transitions between the Sleep state and Awake state based on the sleep and
wake timers.
The wake timer (which is the time the WiFly is asleep) is a 22 bit number of seconds so the maximum
The wake timer (which is the time the WiFly is asleep) is a 22 bit number of seconds so the maximum
The wake timer (which is the time the WiFly is asleep) is a 22 bit number of seconds so the maximum
set wlan ssid my_net
set wlan passphrase my_pass
set sys sleep 30
set sys wake 90
save
reboot
www.rovingnetworks.com
809 University Avenue
0 seconds every 2 minutes you would set the timers as such
set sys sleep <time> time=decimal in seconds.
set sys wake <time> time=decimal in seconds.
•
Los Gatos, CA 95032
Los Gatos, CA 95032
ically go into deep sleep low power mode once the timer counts down to 0.
ically go into deep sleep low power mode once the timer counts down to 0.
~ 29 ~
•
Tel [phone]
• [e-mail]
[e-mail]
WiFlyGSX-um
econds so it can be as high as
WiFly GSX
WiFly GSX
um
9/16/2010