ATA5824-PLQW Atmel, ATA5824-PLQW Datasheet - Page 64

• Manufacturer Part Number: ATA5824-PLQW
• Description: IC TXRX UHF ASK/FSK 48QFN
• Manufacturer: Atmel

Specifications of ATA5824-PLQW

• Frequency: 433 ~ 435MHz; 866 ~ 870MHz
• Data Rate - Maximum: 20kbps
• Modulation Or Protocol: ASK, FSK
• Applications: RKE, TPM, Security Systems
• Power - Output: 10dBm
• Sensitivity: -116dBm
• Voltage - Supply: 2.15 V ~ 3.6 V or 4.4 V ~ 5.25 V
• Current - Receiving: 10.5mA
• Current - Transmitting: 10.5mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -

Table 14-5.
14.3
64
Mode
TX
Full-duplex Operation
ATA5823/ATA5824
TX Modulation Schemes
ASK/_NFSK
0
1
The transceiver is set to full-duplex mode (FD mode) by using the bits OPM0, OPM1 and OPM2
in the control register 1. In FD mode 2 transceiver exchange the content of the TX buffer simul-
taneously. One transceiver must be configured as master and one as slave.
Table 14-6.
Before activating FD mode in both transceivers, the bit rate must be selected in control register 6
(Baud1 = 0, Baud0 = 1). Additionally, in the slave the limits for the Bit-check and the number of
bits to be checked during the Bit-check N
(Lim_min0 ... Lim_min5, Lim_max0 ... Lim_max5, BitChk0, BitChk1).
After activating the FD mode in control register 1, both transceivers are in the startup mode. Dur-
ing the startup mode, in master and slave, the TX data stream can be written in the TX buffer.
In the master the TX data stream consists of preburst, startbit, synchronization pattern (3 bytes)
and maximally 8 bytes of data. The preburst contains a sequence of “11111...”. The minimum
applicable preburst length is 15 bits and can be extended in 8 bit steps up to 95 bits. The value
of the start bit is fixed and must be a 0. The position of the start bit is the LSB in the last byte of
the preburst. The synchronization pattern contains 3 bytes with a fixed value (Byte1: FF hex,
Byte2: 00 hex, Byte3: 00 hex). The data block is user defined and contains maximally 8 bytes. If
the preburst contains more than 39 bits the area for the data block will be equally reduced
ure 14-12 on page
In the slave the TX data stream consists of the synchronization pattern (3 bytes) and also maxi-
mally 8 bytes of data. The synchronization pattern contains 3 bytes with a fixed value (Byte1:
00 hex, Byte2: 7F hex, Byte3: FF hex). The data block is user defined and contains maximally
8 bytes
slave.
OPM2
(Figure 14-12 on page
P_Mode
1
1
X
X
X
X
0
0
1
1
0
0
1
1
Control Register 1
65.)
T_Mode
OPM1
0
0
0
0
1
1
0
0
0
0
1
1
0
1
65). The length of the data block must be equal in the master and
Bit in TX/RX
Data Buffer
Bit-check
X
X
X
X
1
0
1
0
1
0
1
0
OPM0
1
1
must be adjusted in control register 5 and 6
Level on Pin
SDI_TMDI
X
X
X
X
X
X
X
X
1
0
1
0
Full-duplex mode (Master)
Full-duplex mode (Slave)
Function
f
f
ASK
ASK
f
f
FSK_L
FSK_H
off
on
f
f
f
f
RF
f
f
ASK
ASK
ASK
ASK
f
f
FSK_H
FSK_H
FSK_L
FSK_L
4829D–RKE–06/06
OUT
on
off
on
off
f
f
f
f
FSK_H
ASK
ASK
FSK_L
on
off
(Fig-