DP83816AVNG National Semiconductor, DP83816AVNG Datasheet - Page 69

• Manufacturer Part Number: DP83816AVNG
• Description: Ethernet Media Access Controller IC
• Manufacturer: National Semiconductor

Specifications of DP83816AVNG

• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Mounting Type: Surface Mount
• Features: Physical Layer
• Package / Case: 144-LQFP
• Package: 144LQFP
• Standard Supported: IEEE 802.3|IEEE 802.3u|IEEE 802.3x
• Communication Mode: Full Duplex|Half Duplex
• Network Interface: MII
• Data Rate: 10|100 Mbps
• Host Interface: PCI
• Operating Supply Voltage: 3.3 V
• Loopback Mode: Internal
• Maximum Power Dissipation: 0.504 W
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

4.0 Register Set
4.3.6 Auto-Negotiation Link Partner Ability Register
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The content
changes after the successful auto-negotiation if Next-pages are supported.
12:10
Bit
Bit
4:0
15
14
13
9
8
7
6
5
9
8
7
6
Bit Name
Bit Name
Reserved
Selector
TX_FD
TX_FD
10_FD
10_FD
ACK
NP
RF
T4
TX
T4
TX
10
Offset: 0094h
(Continued)
Tag: ANLPAR
100BASE-T4 Support: Default: 0/ RO
1= 100BASE-T4 is supported by the local device
0 = 100BASE-T4 not supported
100BASE-TX Full Duplex Support: Default: dependent on setting of the ANEG_SEL in the CFG register
1 = 100BASE-TX Full Duplex is supported by the local device
0 = 100BASE-TX Full Duplex not supported
100BASE-TX Support: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
1 = 100BASE-TX is supported by the local device
0 = 100BASE-TX not supported
10BASE-T Full Duplex Support: Default: dependent on setting of the ANEG_SEL in the CFG register
1 = 10BASE-T Full Duplex is supported by the local device
0 = 10BASE-T Full Duplex not supported
10BASE-T Support: Default: dependent on the setting of the ANEG_SEL bits in the CFG register
1 = 10BASE-T is supported by the local device
0 = 10BASE-T not supported
Protocol Selection Bits: Default: <00001>
These bits contain the binary encoded protocol selector supported by this port. <00001> indicates that
this device supports IEEE 802.3u.
Next Page Indication:
0 = Link Partner does not desire Next Page Transfer
1 = Link Partner desires Next Page Transfer
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word
0 = Not acknowledged
The Device's Auto-Negotiation state machine will automatically control this bit based on the incoming FLP
bursts.
Remote Fault:
1 = Remote Fault indicated by Link Partner
0 = No Remote Fault indicated by Link Partner
Reserved for Future IEEE use: Write as 0, read as 0
100BASE-T4 Support:
1 = 100BASE-T4 is supported by the Link Partner
0 = 100BASE-T4 not supported by the Link Partner
100BASE-TX Full Duplex Support:
1 = 100BASE-TX Full Duplex is supported by the Link Partner
0 = 100BASE-TX Full Duplex not supported by the Link Partner
100BASE-TX Support:
1 = 100BASE-TX is supported by the Link Partner
0 = 100BASE-TX not supported by the Link Partner
10BASE-T Full Duplex Support:
1 = 10BASE-T Full Duplex is supported by the Link Partner
0 = 10BASE-T Full Duplex not supported by the Link Partner
Access: Read Only
Size: 16 bits
69
Description
Description
Hard Reset: 0000h
www.national.com