PIC18F2410-E/ML Microchip Technology, PIC18F2410-E/ML Datasheet - Page 162

• Manufacturer Part Number: PIC18F2410-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2410-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core: PIC
• Processor Series: PIC18F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 768 B
• On-chip Adc: 10 bit
• Number Of Programmable I/os: 25
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Mounting Style: SMD/SMT
• Height: 0.88 mm
• Interface Type: EUSART, I2C, MSSP, SPI
• Length: 6 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 6 mm
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F2X1X/4X1X
REGISTER 16-4:
DS39636D-page 164
bit 7
bit 6
bit 5
bit 4
bit 3-0
bit 7
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPBUF register was attempted while the I
0 = No collision
In Slave Transmit mode:
1 = The SSPBUF register is written while it is still transmitting the previous word (must be
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit.
SSPOV: Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte (must be
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode.
SSPEN: Synchronous Serial Port Enable bit
1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: SCK Release Control bit
In Slave mode:
1 = Release clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode.
SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
1111 = I
1110 = I
1011 = I
1000 = I
0111 = I
0110 = I
Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.
Legend:
R = Readable bit
-n = Value at POR
SSPCON1: MSSP CONTROL REGISTER 1 (I
WCOL
R/W-0
Note:
transmission to be started (must be cleared in software)
cleared in software)
cleared in software)
2
2
2
2
2
2
C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
C Firmware Controlled Master mode (Slave Idle)
C Master mode, clock = F
C Slave mode, 10-bit address
C Slave mode, 7-bit address
When enabled, the SDA and SCL pins must be properly configured as input or
output.
SSPOV
R/W-0
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
OSC
R/W-0
CKP
/(4 * (SSPADD + 1))
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
2
C MODE)
SSPM2
2
R/W-0
C conditions were not valid for a
© 2009 Microchip Technology Inc.
x = Bit is unknown
SSPM1
R/W-0
SSPM0
R/W-0
bit 0