PIC18F2410-E/ML Microchip Technology, PIC18F2410-E/ML Datasheet - Page 256

• Manufacturer Part Number: PIC18F2410-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2410-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core: PIC
• Processor Series: PIC18F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 768 B
• On-chip Adc: 10 bit
• Number Of Programmable I/os: 25
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Mounting Style: SMD/SMT
• Height: 0.88 mm
• Interface Type: EUSART, I2C, MSSP, SPI
• Length: 6 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 6 mm
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F2X1X/4X1X
22.9
The LVP Configuration bit enables Single-Supply ICSP
Programming (formerly known as Low-Voltage ICSP
Programming or LVP). When Single-Supply Program-
ming is enabled, the microcontroller can be programmed
without requiring high voltage being applied to the
MCLR/V
dedicated to controlling Program mode entry and is not
available as a general purpose I/O pin.
While programming, using Single-Supply Program-
ming mode, V
as in Normal Execution mode. To enter Programming
mode, V
DS39636D-page 258
Note 1: High-voltage programming is always
PP
DD
2: By
3: When Single-Supply Programming is
4: When LVP is enabled, externally pull the
Single-Supply ICSP Programming
/RE3 pin, but the RB5/KBI1/PGM pin is then
is applied to the PGM pin.
available, regardless of the state of the
LVP bit or the PGM pin, by applying V
to the MCLR pin.
enabled in unprogrammed devices (as
supplied from Microchip) and erased
devices.
enabled, the RB5 pin can no longer be
used as a general purpose I/O pin.
PGM pin to V
execution.
DD
is applied to the MCLR/V
default,
SS
Single-Supply
to allow normal program
PP
ICSP
/RE3 pin
IHH
is
If Single-Supply ICSP Programming mode will not be
used, the LVP bit can be cleared. RB5/KBI1/PGM then
becomes available as the digital I/O pin, RB5. The LVP
bit may be set or cleared only when using standard
high-voltage programming (V
V
standard high-voltage programming is available and
must be used to program the device.
Memory that is not code-protected can be erased using
either a block erase, or erased row by row, then written
at any specified V
erased, a block erase is required. If a block erase is to
be performed when using Low-Voltage Programming,
the device must be supplied with V
PP
/RE3 pin). Once LVP has been disabled, only the
DD
. If code-protected memory is to be
© 2009 Microchip Technology Inc.
IHH
applied to the MCLR/
DD
of 4.5V to 5.5V.