N6761A AGILENT TECHNOLOGIES, N6761A Datasheet - Page 12
![POWER SUPPLY, BENCH, 50V, 50W](/photos/21/58/215861/4091023_sml.jpg)
N6761A
Manufacturer Part Number
N6761A
Description
POWER SUPPLY, BENCH, 50V, 50W
Manufacturer
AGILENT TECHNOLOGIES
Datasheet
1.N6751A.pdf
(20 pages)
Specifications of N6761A
Power Supply Output Type
Variable
No. Of Outputs
1
Output Voltage
50V
Output Current
1.5A
Power Rating
50W
Input Voltage
100V AC To 240 V AC
Length
596.9mm
Width
432.5mm
Height
44.45mm
Lead Free Status / RoHS Status
na
N675xA Modules:
The automatic setting adjust-
ment done in the 662xA when
the range changes will not occur
because it is no longer necessary
due to the autoranging capabil-
ity of the N675xA. Since there
is no range switching, the
“coupled parameter” (CP) bit
is never set.
Range Programming
25 W and 50 W
Precision Outputs:
The range can be set by using
the “VRSET” or “IRSET” com-
mands. The power supply will
automatically pick the range
that the value sent fits into. If
the value sent requires a range
change (high to low or low to
high) the “coupled parameter”
(CP) bit is set.
N676xA Modules:
The functionality is the same
as above, but the ranges are
different.
the ranges for the different
outputs.
Range
High
Low
Table 6. Output/Measurement Ranges
Table 6
25 W Precision
0-50 V/0-500 mA
0-7 V/0-15 mA
below shows
50 W Precision
0-50 V/0-2 A
0-16 V/0-200 mA
Functions that operate
differently or are missing
For compatibility, most
commands from the 662xA
language are accepted, however,
some commands do nothing.
Commands that “do nothing”
are accepted and do not pro-
duce an error, but no function
is performed. The commands
that are not accepted will
return “Error 203, Compatibility
function not implemented”.
ID? Query
The “ID?” query, when sent to
the N6700A/B will always
return the model number of
the mainframe, which will be
either “N6700A” or “N6700B”.
OCRST and OVRST
662xA: “OCRST <ch>” returns
the specified channel to the
settings it had prior to being
turned off by the overcurrent
protection circuit, clearing
ONLY the OC condition.
“OVRST <ch>” attempts to reset
the overvoltage crowbar circuit
in the specified output channel,
clearing only the OV condition.
N6761A
0-50 V/0-1.5 A
0-5.5 V/0-100 mA
12
N6762A
0-50 V/0-3 A
0-5.5 V/0-100 mA
N67xxA Modules: Both OVRST
and OCRST will reset ALL
latched protection functions
for the specified channel.
Calibration
None of the 662xA calibration
commands are provided in the
compatibility language of the
N67xxA modules. Calibration
must be done exclusively in the
SCPI language format. Use of
any of the 662xA’s calibration
command set will result in an
error message. Please refer
to Calibration in the N6700
User’s Guide for the calibration
procedure.
Multiple Output Storage & Recall
6621A, 6622A, 6623A,
6624A, 6627A:
These models have 10 internal
registers, which have the
following characteristics:
• All registers (1-10) can store
• When a register is recalled
• At power-on, all registers
the voltage (VSET) and
current (ISET) settings for
all the outputs.
“RCL <reg>”, the outputs are
set sequentially (1,2,3,4).
(1-10), because they are all
volatile, are reset to zero
volts and minimum current.