TLE7188F Infineon Technologies, TLE7188F Datasheet - Page 16

no-image

TLE7188F

Manufacturer Part Number
TLE7188F
Description
IC DRIVER 3PH BRIDGE 48-VQFN
Manufacturer
Infineon Technologies
Type
High Side/Low Sider
Datasheet

Specifications of TLE7188F

Applications
DC Motor Driver, 3 Phase
Number Of Outputs
1
Voltage - Supply
5.5 V ~ 28 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
48-VFQFN Exposed Pad
Product
H-Bridge Drivers
Rise Time
400 ns
Fall Time
230 ns
Supply Voltage (min)
5.5 V
Supply Current
110 mA
Maximum Operating Temperature
+ 150 C
Mounting Style
SMD/SMT
Bridge Type
Half Bridge
Minimum Operating Temperature
- 40 C
Number Of Drivers
6
Packages
PG-VQFN-48
Operating Range
5.5 - 28.0 V
Iq
30 ?A
Turn On/off Current
1.5/ 1.5 A
D.c.-range @ 20khz
0...100%
Numbers Of Integrated Opamps For Load Current Measurement
3.0
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output
-
Voltage - Load
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
SP000105749

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TLE7188F
Manufacturer:
INFINEON
Quantity:
13 900
Part Number:
TLE7188F
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
5.2
5.2.1
The TLE7188F provides a short circuit protection for the external MOSFETs. It is a monitoring of the drain-source
voltage of the external MOSFETs. As soon as this voltage is higher than the short circuit detection limit, a capacitor
will be charged. The high side and the low side output stage of the same half bridge use the same capacitor (see
Figure 3
charge and discharge ratio is specified by means of duty cycles at which a short circuit is detected or not detected.
After a delay of about 12 µs all external MOSFETs will be switched off until the driver is reset by the ENA pin. The
error flag is set.
The drain-source voltage monitoring of the short circuit detection for a certain external MOSFET is active as soon
as the corresponding input is set to "on" and the dead time is expired.
The short circuit detection level is adjustable in an analogue manner by the voltage setting at the SCDL pin. There
is a 1:1 translation between the voltage applied to the SCDL pin and the drain-source voltage limit. For instance
to trigger the SCD circuit at 1 V drain-source voltage, the SCDL pin must be set to 1 V as well. The drain-source
voltage limit can be chosen between 0.5 ... 2.5 V.
A setting of 5 V at the SCDL pin will disable the short circuit protection function. Disabling the short circuit
protection function has no impact on the overcurrent warning (see next chapter).
5.2.2
The TLE7188F offers the possibility to shut down the output stages if a current threshold is reached (see
The output of the current sense OpAmp is connected to an integrated comparator, comparing the amplified current
sense signal with an external adjustable threshold value. After the comparator a blanking time (1.5 µs typ.) is
implemented to avoid false triggering caused by overswing of the current sense signal.
If the overcurrent situation is detected, only an error signal is given. During overcurrent the driver IC works
normally. The error signal disappears as soon as the current decreases below the overcurrent limit set on the
VTHOC pin. The error signal disappears as well when the current commutates from the low side MOSFET to the
associated high side MOSFET (no current through the shunt resistor).
It is the decision of the user to react on the over current signal by modifying the Ixx patterns to lower the current.
The overcurrent warning can be disabled by connecting the overcurrent threshold pin to GND (V
5.2.3
In bridge applications it has to be assured that the external high side and low side MOSFETs are not "on" at the
same time, connecting directly the battery voltage to GND. The dead time generated in the TLE7188F is fixed to
a minimum value. This function assures a minimum dead time if the input signals coming from the µC are faulty.
The exact dead time of the bridge is usually controlled by the PWM generation unit of the µC.
In addition to this dead time, the TLE7188F provides a locking mechanism, avoiding that both external MOSFETs
of one half bridge can be switched on at the same time. This functionality is called shoot through protection.
If the command to switch on both high and low side switches in the same half bridge is given at the input pins, the
command will be ignored.
5.2.4
The TLE7188F has an integrated under voltage shut down, to assure that the behavior of the device is predictable
in all voltage ranges.
Data Sheet
). This capacitor is discharged permanently with a current which is smaller than the charging current. This
Protection and Diagnostic Functions
Short Circuit Protection
Over current Warning
Dead Time and Shoot Through Protection
Under voltage Shut Down
16
Protection and Diagnostic Functions
V2.1, 2007-06-20
THOC
TLE7188F
Figure 4
= 0 V).
).

Related parts for TLE7188F