F39-EU1E Omron, F39-EU1E Datasheet - Page 523

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

Wiring

Circuit Connection Example

Wiring

[Reference] Crimp Terminals

Manufacturer

J.S.T. Mfg Co.

(+)

(−)

(+)

(−)

Direct opening contacts used for safety circuit inputs are indicated

with the

opening contacts.

Connect the indicators in parallel to the auxiliary circuits or

terminals E1 and E2. Do not connect the indicators in parallel with

the direct opening contact. If the indicators are broken, a

short-circuit current may flow, causing equipment to malfunction.

Do not switch circuits for two or more standard loads at the same

time. Doing so may adversely affect insulation performance.

The 24 VDC solenoid terminals have polarity (E1: +, E2: ).

Confirm the polarity before wiring.

The contact ON/OFF timing for Switches is not synchronized.

Confirm performance before application.

Do not wire the Switch while power is being supplied. Doing so may

result in electric shock.

Do not let particles, such as small pieces of lead wire, enter the

switch body when wiring.

Make sure that the wiring does not hide the LED indicator when

wiring E1/E2 or O1/O2.

When connecting to the terminals via insulating tube and M3.5

crimp terminals, arrange the crimp terminals so that they do not

rise up onto the case or the cover.

Applicable lead wire size: AWG22 to AWG18 (0.3 to 0.75 mm

Use lead wires of an appropriate length. Not doing so may result in

excess length causing the cover to rise and not fit properly.

Do not pull on the lead wires with excessive force. Doing so may

disconnect them.

Do not push crimp terminals into gaps in the case interior. Doing so

may cause damage or deformation of the case.

Crimp terminal

LED

dz dia: 4.3 mm

D dia: 4.0 mm

Lock Monitor

Switch

B: 6.6 mm

F: 6.3 mm

L: 18.6 mm

t: 0.8 mm

I: 9.0 mm

mark. Terminals 12-41 and terminals 22-51 have direct

Correct

FN1.25-M4 (F Type)

N1.25-M4 (Straight Type)

http://www.ia.omron.com/

Terminal screw

D dia.

Model

Door Open/Closed

Detection Switch

dz dia.

Incorrect

To safety circuit

To control circuit

Processing the Conduit Opening

Recommended Connectors

Use a connector with a screw section not exceeding 9 mm.

Otherwise, the screws will protrude into the case interior. The

connectors given in the following table have connectors with screw

sections not exceeding 9 mm. Use the following connectors to ensure

conformance to IP67.

Use LAPP connectors together with Seal Packing (JPK-16, GP-13.5,

or GPM20), and tighten to the applicable torque. Seal Packing is sold

separately.

Other Precautions

G1/2

PG13.5

M20

1/2-14NPT

Connect a recommended connector to the opening of the conduit

and tighten the connector to the proper torque. The case may be

damaged if excessive tightening torque is applied.

When using a 1/2-14NPT conduit, wind sealing tape around the

conduit end of the connector so that the enclosure will conform to

IP67.

Make sure that the outer diameter of the cable connected to the

connector is correct.

Attach a conduit cap to the unused conduit opening when wiring

and tighten it to a suitable torque. The conduit cap is provided with

the Switch.

LAPP is a German manufacturer.

For a 1/2-14NPT conduit, use the above connector after attaching

the provided Adaptor to the Switch and wrapping it with sealing

tape.

A Guard Lock Safety-door Switch will heat when power is supplied

to the solenoid. Do not touch these Switches.

Size

LAPP

Manufacturer

ST-PF1/2

ST-13.5

ST-M20

ST-NPT1/2

1.5

Model

5380-1002

5301-5030

5311-1020

5301-6030

6.0 to 12.0 mm

7.0 to 13.0 mm

6.0 to 12.0 mm

Applicable

diameter

cable

D4JL

F39-EU1E Omron, F39-EU1E Datasheet - Page 523

F39-EU1E

Specifications of F39-EU1E

Related parts for F39-EU1E