IDT77V126L200TFI IDT, Integrated Device Technology Inc, IDT77V126L200TFI Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT77V126L200TFI
Manufacturer Part Number
IDT77V126L200TFI
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT77V126L200TFI.pdf
(30 pages)
Specifications of IDT77V126L200TFI
Number Of Channels
1
Type Of Atm Phy Interface
UTOPIA
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Pin Count
64
Mounting
Surface Mount
Lead Free Status / RoHS Status
Not Compliant
Functional Description
Transmission Convergence (TC) Sub Layer
and synchronization. Under control of a switch interface or Segmenta-
tion and Reassembly (SAR) unit, the 25.6Mbps ATM PHY accepts a 53-
byte ATM cell, scrambles the data, appends a command byte to the
beginning of the cell, and encodes the entire 53 bytes before transmis-
sion. These data transformations ensure that the signal is evenly distrib-
uted across the frequency spectrum. In addition, the serialized bit
stream is NRZI coded. An 8kHz timing sync pulse may be used for
isochronous communications.
is distinguished by an escape symbol followed by one of 17 encoded
symbols. Together, this byte forms one of seventeen possible command
bytes. Three command bytes are defined:
usage:
of-cell command byte which resets both the transmitter-scrambler and
receiver-descrambler pseudo-random nibble generators (PRNG) to their
initial states. The following cell illustrates the insertion of a start-of-cell
command without scrambler/descrambler reset. During this cell's trans-
mission, an 8kHz timing sync pulse triggers insertion of the X_8 8kHz
timing marker command byte.
face. An ATM layer device transfers a cell into the 77V126L200 across
the Utopia transmit bus. This cell enters a 3-cell deep transmit FIFO.
Once a complete cell is in the FIFO, transmission begins by passing the
cell, four bits (MSB first) at a time to the 'Scrambler'.
against the 4 high order bits (X(t), X(t-1), X(t-3)) of a 10 bit pseudo-
random nibble generator (PRING). Its function is to provide the appro-
priate frequency distribution for the signal across the line.
IDT77V126L200
Introduction
The TC sub layer defines the line coding, scrambling, data framing
Data Structure and Framing
Each 53-byte ATM cell is preceded with a command byte. This byte
1. X_X (read: 'escape' symbol followed by another 'escape'): Start-
2.
3.
Below is an illustration of the cell structure and command byte
{X_X} {53-byte ATM cell} {X_4} {53-byte ATM {X_8} cell}...
In the above example, the first ATM cell is preceded by the X_X start-
Transmission Description
Refer to Figure 2. Cell transmission begins with the PHY-ATM Inter-
The ‘Scrambler’ takes each nibble of data and exclusive-ORs them
of-cell with scrambler/descrambler reset.
descrambler reset.
command byte is generated when the 8kHz sync pulse is
detected, and has priority over all line activity (data or command
bytes). It is transmitted immediately when the sync pulse is
detected. When this occurs during a cell transmission, the data
transfer is temporarily interrupted on an octet boundary, and the
X_8 command byte is inserted. This condition is the only allowed
interrupt in an otherwise contiguous transfer.
X_4 ('escape' followed by '4'): Start-of-cell without scrambler/
X_8 ('escape' followed by '8'): 8kHz timing marker. This
6 of 30
whether the processed nibble is part of a data or command byte. Note
however that only data nibbles are scrambled. The entire command
byte (X _C) is NOT scrambled before it's encoded (see diagram for
illustration).
The PRNG is based upon the following polynomial:
be generated from the following equations:
X(t+1).
time an X_X command is sent. An X_X command is initiated only at the
beginning of a cell transfer after the PRNG has cycled through all of its
states (2
after power on will also be accompanied with an X_X command byte.
Each time an X_X command byte is sent, the first nibble after the last
escape (X) nibble is XOR'd with 1111b (PRNG = 3FFx).
possibility of a reset PRNG start-of-cell command and a timing marker
command occurring consecutively does exist (e.g. X_X_X_8). In this
case, the detection of the last two consecutive escape (X) nibbles will
cause the PRNG to reset to its initial 3FFx state. Therefore, the PRNG is
clocked only after the first nibble of the second consecutive escape pair.
nibbles are further encoded using a 4b/5b process. The 4b/5b scheme
ensures that an appropriate number of signal transitions occur on the
line. A total of seventeen 5-bit symbols are used to represent the sixteen
4-bit data nibbles and the one escape (X) nibble. The table below lists
the 4-bit data with their corresponding 5-bit symbols:
The PRNG is clocked every time a nibble is processed, regardless of
X
With this polynomial, the four output data bits (D3, D2, D1, D0) will
D3 = d3 xor X(t-3)
D2 = d2 xor X(t-2)
D1 = d1 xor X(t-1)
D0 = d0 xor X(t)
The following nibble is scrambled with X(t+4), X(t+3), X(t+2), and
A scrambler lock between the transmitter and receiver occurs each
Because a timing marker command (X_8) may occur at any time, the
Once the data nibbles have been scrambled using the PRNG, the
10
+ X
10
7
- 1 = 1023 states). The first valid ATM data cell transmitted
+ 1
ESC(X) = 00010
0010
0110
1010
1110
Data
0000
0100
1000
1100
Data
Symbol
Symbol
01010
01110
11010
11110
10101
00111
10010
10111
Data
0001
0101
1001
1101
0011
0111
1011
1111
Data
Symbol
Symbol
December 2004
01001
01101
11001
11101
01011
01111
11011
11111
3505 drw 05a
.
.