IDT77V126L200TFI IDT, Integrated Device Technology Inc, IDT77V126L200TFI Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
IDT77V126L200TFI
Manufacturer Part Number
IDT77V126L200TFI
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.IDT77V126L200TFI.pdf
(30 pages)
Specifications of IDT77V126L200TFI
Number Of Channels
1
Type Of Atm Phy Interface
UTOPIA
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Pin Count
64
Mounting
Surface Mount
Lead Free Status / RoHS Status
Not Compliant
properties. Among them is the fact that the output data bits can be
represented by a set of relatively simple symbols;
whether a timing marker command (X_8) or a start-of-cell command was
sent (X_X or X_4). If a start-of-cell command is detected, the next 53
bytes received are decoded and forwarded to the descrambler. (See the
TC Receive Block Diagram).
encoder. The NRZI code transitions the wire voltage each time a '1' bit is
sent. This, together with the previous encoding schemes guarantees
that long run lengths of either '0' or '1's are prevented. Each symbol is
shifted out with its most significant bit sent first.
line active by continuing to transmit valid symbols. But it does not
transmit another start-of-cell command until it has another cell for trans-
mission. The 77V126L200 never generates idle cells.
lated automatically across the first 4 bytes of the cell header, depending
upon the setting of bit 5 of the LED Driver and HEC Status/Control
Register (0x03). This byte is then either inserted as a replacement of the
fifth byte transferred to the PHY by the external system, or the cell is
transmitted as received. A third operating mode provides for insertion of
"Bad" HEC codes which may aid in communication diagnostics. These
modes are controlled by the LED Driver and HEC Status/Control Regis-
ters.
in reverse. The data is NRZI decoded before each symbol is reassem-
bled. The symbols are then sent to the 5b/4b decoder, followed by the
Command Byte Interpreter, De-Scrambler, and finally through a FIFO to
the UTOPIA interface to an ATM Layer device.
IDT77V126L200
This encode/decode implementation has several very desirable
On the receiver, the decoder determines from the received symbols
The output of the 4b/5b encoder provides serial data to the NRZI
When no cells are available to transmit, the 77V126L200 keeps the
Transmit HEC Byte Calculation/Insertion
Byte #5 of each ATM cell, the HEC (Header Error Control) is calcu-
Receiver Description
The receiver side of the TC sublayer operates like the transmitter, but
ATM Cell Format
!
!
Run length is limited to <= 5;
Disparity never exceeds +/- 1.
Bit 7
Payload Byte 48
Payload Byte 1
Header Byte 1
Header Byte 2
Header Byte 3
Header Byte 4
UDF
Bit 0
8 of 30
errors, it does not attempt to correct them.
of the 4b/5b decoder uses feedback from the 4b/5b decoder to deter-
mine if it is not properly "framed" on the 5-bit symbols being received. If
not properly framed, it will shift its framing, one bit at a time, until it
achieves proper symbol framing. Receipt of an Escape (X) symbol will
also force proper symbol framing.
interrupt if the line is deemed 'bad'. The Interrupt Status Register
contains a Good Signal Bit (bit 6, set to 0 = Bad signal initially) which
shows the status of the line per the following algorithm:
set to 7. When the clock ticks for 1,024 cycles (32MHz clock, 1,024
cycles = 204.8 symbols) and no "bad symbol" has been received, the
counter decreases by one. However, if at least one "bad symbol" is
detected during these 1,024 clocks, the counter is increased by one, to
a maximum of 7. The Good Signal Bit is set to 1 when this counter
reaches 0. The Good Signal Bit could be set to 1 as quickly as 1,433
symbols (204.8 x 7) if no bad symbols have been received.
a "Good" status). When the clock ticks for 1,024 cycles (32MHz clock,
1,024 cycles = 204.8 symbols) and there is at least one "bad symbol",
the counter increases by one. If it detects all "good symbols" and no
"bad symbols" in the next time period, the counter decreases by one.
The "Bad Signal" is declared when the counter reaches 7. The Good
Signal Bit could be set to 0 as quickly as 1,433 symbols (204.8 x 7) if at
least one "bad symbol" is detected in each of seven consecutive groups
of 204.8 symbols.
feature which is essential for some applications requiring synchroniza-
tion for voice or video, and unnecessary for other applications. When
unused, TXREF should be tied high. Also note that it is not limited to
8kHz, should a different frequency be desired. When looped, a received
X_8 command byte causes one to be generated on the transmit side.
negative pulse on RXREF.
PHY-ATM Interface
standardized by the ATM Forum. It is used for transferring ATM cells
and has separate transmit and receive channels and specific hand-
shaking protocols. It is defined in ATM Forum documents af-phy-0017
and af-phy-0039.
Note that although the IDT77V126L200 can detect symbol and HEC
Good Signal Bit
Upon resetting the device or re-establishing a serial link, logic in front
The IDT77V126L200 monitors line conditions and can provide an
To declare 'Good Signal' (from "Bad" to "Good")
There is an up-down counter that counts from 7 to 0 and is initially
To declare 'Bad Signal' (from "Good" to "Bad")
The same up-down counter counts from 0 to 7 (being at 0 to provide
8kHz Timing Marker
The 8kHz timing marker, described earlier, is a completely optional
A received X_8 command byte causes the 77V126L200 to issue a
UTOPIA Level 1 is a Physical (PHY) Layer to ATM Layer interface
December 2004