SSTU32866EC-S NXP Semiconductors, SSTU32866EC-S Datasheet - Page 9
![](/photos/31/41/314104/sot536-1_sml.jpg)
SSTU32866EC-S
Manufacturer Part Number
SSTU32866EC-S
Description
Manufacturer
NXP Semiconductors
Datasheet
1.SSTU32866EC-S.pdf
(29 pages)
Specifications of SSTU32866EC-S
Logic Family
SSTU
Logical Function
Registered Buffer
Number Of Elements
1
Number Of Bits
25
Number Of Inputs
25
Number Of Outputs
25
High Level Output Current
-8mA
Low Level Output Current
8mA
Package Type
LFBGA
Propagation Delay Time
3ns
Operating Supply Voltage (typ)
1.8V
Operating Supply Voltage (max)
1.9V
Operating Supply Voltage (min)
1.7V
Clock-edge Trigger Type
Posit/Negat-Edge
Polarity
Non-Inverting
Technology
CMOS
Frequency (max)
450(Min)MHz
Mounting
Surface Mount
Pin Count
96
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Not Compliant
Philips Semiconductors
9397 750 14181
Product data sheet
cascaded to the PAR_IN of the second register. The QERR output of the first register is
left floating and the valid error information is latched on the QERR output of the second
register.
If an error occurs and the QERR output is driven LOW, it stays latched LOW for two clock
cycles or until RESET is driven LOW. The DIMM-dependent signals (DCKE, DCS, DODT,
and CSR) are not included in the parity check computation.
The device supports low-power standby operation. When RESET is LOW, the differential
input receivers are disabled, and undriven (floating) data, clock and reference voltage
(V
outputs are forced LOW. The LVCMOS RESET input must always be held at a valid logic
HIGH or LOW level.
The device also supports low-power active operation by monitoring both system chip
select (DCS and CSR) inputs and will gate the Qn and PPO outputs from changing states
when both DCS and CSR inputs are HIGH. If either DCS or CSR input is LOW, the Qn
and PPO outputs will function normally. The RESET input has priority over the DCS and
CSR control and when driven LOW will force the Qn and PPO outputs LOW, and the
QERR output HIGH. If the DCS control functionality is not desired, then the CSR input can
be hard-wired to ground, in which case, the set-up time requirement for DCS would be the
same as for the other Dn data inputs. To control the low-power mode with DCS only, then
the CSR input should be pulled up to V
To ensure defined outputs from the register before a stable clock has been supplied,
RESET must be held in the LOW state during power-up.
In the DDR2 RDIMM application, RESET is specified to be completely asynchronous with
respect to CK and CK. Therefore, no timing relationship can be guaranteed between the
two. When entering reset, the register will be cleared and the Qn outputs will be driven
LOW quickly, relative to the time to disable the differential input receivers. However, when
coming out of reset, the register will become active quickly, relative to the time to enable
the differential input receivers. As long as the data inputs are LOW, and the clock is stable
during the time from the LOW-to-HIGH transition of RESET until the input receivers are
fully enabled, the design of the SSTU32866 must ensure that the outputs will remain
LOW, thus ensuring no glitches on the output.
REF
) inputs are allowed. In addition, when RESET is LOW all registers are reset, and all
Rev. 02 — 11 November 2004
1.8 V DDR2 configurable registered buffer with parity
DD
through a pull-up resistor.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
SSTU32866
9 of 29