V23818K305L56 Infineon Technologies, V23818K305L56 Datasheet
V23818K305L56
Specifications of V23818K305L56
Related parts for V23818K305L56
V23818K305L56 Summary of contents
Page 1
Small Form Factor Multimode 850 nm 1.0625 Gbit/s Fibre Channel 1.25 Gigabit Ethernet Transceiver 2x5 Pinning with LC™ Connector Extended Temperature Range (–40°C to 85°C) Features • Small Form Factor (SFF) transceiver • Fully compatible with Fibre Channel and Gigabit ...
Page 2
Pin Configuration Tx Rx Figure 1 Pin Description Pin Symbol Level/Logic No Ground EEr V 2 Power supply CCr 3 SD LVTTL output 4 RD– LVPECL output 5 RD+ LVPECL output V 6 Power supply CCt V 7 ...
Page 3
EEr EEt Connect pins 1 and 7 to signal ground CCr CCt A 3 power supply must be applied at pins 2 and 6. A recommended power supply filter network is given ...
Page 4
Description The Infineon Fibre Channel / Gigabit Ethernet multimode transceiver – part of Infineon SFF family – is compatible to the Physical Medium Depend (PMD) sublayer and baseband medium, type 1000 Base-SX (short wavelength) as specified in IEEE Std 802.3 ...
Page 5
Functional Description of 2x5 Pin Row Transceiver This transceiver is designed to transmit serial data via multimode cable. TxDis TD TD+ RD RD+ SD Figure 2 Functional Diagram The receiver component converts the optical serial data into PECL compatible electrical ...
Page 6
Regulatory Compliance Feature ESD: Electrostatic Discharge to the Electrical Pins Immunity: Against Electrostatic Discharge (ESD) to the Duplex LC Receptacle Immunity: Against Radio Frequency Electromagnetic Field Emission: Electromagnetic Interference (EMI) Dimensions in (mm) inches Figure 3 Transceiver Pitch Data Sheet ...
Page 7
Technical Data Absolute Maximum Ratings Parameter Package Power Dissipation Data Input Levels (PECL) Differential Data Input Voltage Swing Operating Ambient Temperature Storage Ambient Temperature Soldering Conditions, Temp/Time (MIL-STD 883C, Method 2003) V max. CC ECL-Output Current Data Exceeding any one ...
Page 8
Recommended Operating Conditions Parameter Ambient Temperature Power Supply Voltage Transmitter Differential Data Input Voltage Swing Receiver Input Center Wavelength The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Transmitter Electro-Optical Characteristics ...
Page 9
Receiver Electro-Optical Characteristics Parameter Sensitivity (Average Power) Saturation (Average Power) Min. Optical Modulation Amplitude 2) Stressed Receiver Sensitivity 50 µm Fiber Stressed Receiver Sensitivity 62.5 µm Fiber Signal Detect Assert Level Signal Detect Deassert Level Signal Detect Hysteresis Signal Detect ...
Page 10
Eye Safety This laser based multimode transceiver is a Class 1 product. It complies with IEC 60825- 1/A2: 2001 and FDA performance standards for laser products (21 CFR 1040.10 and 1040.11) except for deviations pursuant to Laser Notice 50, dated ...
Page 11
Application Notes Small Form Factor Pinning Comparison The drawing below gives you a comparison between the different pinnings 2x5, 2x6, 2x10. Dimension for diameter and distance of additional pins is similar to the existing dimensions of the other pins. RS ...
Page 12
EMI Recommendations To avoid electromagnetic radiation exceeding the required limits please take note of the following recommendations. When high speed components are found on a PCB (multiplexers, clock recoveries etc.) any opening of the chassis may produce radiation also at ...
Page 13
Recommended Termination Scheme 2x5 AC/AC Transceiver Laser 100 Driver SFF Transceiver Signal Detect Limiting RD Pre- Amplifier Amp RD+ C1/2/3 = 4.7 ... 10 F C4/5/6 = Design criterion is the resonance frequency only. The self resonant frequency of the ...
Page 14
Package Outlines Dimensions in mm [inches] Figure 8 Data Sheet V23818-K305-L56 a) recommended bezel position Drawing shown is with collar 14 Package Outlines File: 1212 2004-08-27 ...
Page 15
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...