BTS410G2E3062A Infineon Technologies, BTS410G2E3062A Datasheet
BTS410G2E3062A
Specifications of BTS410G2E3062A
Available stocks
Related parts for BTS410G2E3062A
BTS410G2E3062A Summary of contents
Page 1
... Loss of ground and loss Electrostatic discharge (ESD) protection Application C compatible power switch with diagnostic feedback for 12 V and grounded loads Most suitable for inductive loads Replaces electromechanical relays, fuses and discrete circuits General Description N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic feedback, monolithically integrated in Smart SIPMOS functions ...
Page 2
... Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm connection. PCB is vertical without blown air. Semiconductor Group Function Logic ground Input, activates the power switch in case of logical high signal Positive power supply voltage, the tab is shorted to this pin Diagnostic feedback, low on failure Output to the load ...
Page 3
... Electrical Characteristics Parameter and Conditions ° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (pin 1 Nominal load current, ISO Norm (pin 0 ° Output current (pin ) while GND disconnected or 5 GND pulled up page 7, T =-40...+150°C j Turn-on time ...
Page 4
... Parameter and Conditions ° unless otherwise specified j bb Protection Functions Initial peak short circuit current limit (pin Repetitive short circuit shutdown current limit (see timing diagrams, page 10 Output clamp (inductive load switch off mA OUT bb ON(CL Thermal overload trip temperature Thermal hysteresis ...
Page 5
Truth Table Input- Output level level Normal L L operation Open load Short circuit GND H L Short circuit Overtem perature ...
Page 6
Terms PROFET GND GND R GND Input circuit (ESD protection ESD GND ...
Page 7
... OUT OUT IN IN(T+) If other external inductive loads L are connected to the PROFET, additional elements like D are necessary. Inductive Load switch-off energy dissipation E bb OUT 5 = Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET is E OUT 5 with an approximate solution for R ...
Page 8
... Maximum allowable load inductance for a single switch off ); T = 150° 150°C const., L j,start [mH] 10000 1000 100 1.5 1.75 2 2.25 Semiconductor Group Typ. transient thermal impedance chip case D), D=t thJC p Z [K/W] thJC 10 1 0.1 0.01 1E-5 2.5 2. [A] 8 BTS 410 G2 ...
Page 9
... Options Overview all versions: High-side switch, Input protection, ESD protection, load dump and reverse battery protection with 150 ground Type Logic version Overtemperature protection with hysteresis T j >150 °C, latch function >150 °C, with auto-restart on cooling Short circuit to GND protection switches off when V > ...
Page 10
... Timing diagrams Figure 1a: V turn on OUT ST open drain proper turn on under all conditions Figure 2a: Switching an inductive load IN t d(ST OUT L(OL the time constant of load is too large, open-load-status may occur Semiconductor Group Figure 3a: Turn on into overload, Short circuit shut down by overtempertature, reset by cooling ...
Page 11
Figure 5a: Open load: detection in ON-state, turn on/off to open load IN t d(ST OUT I L open Figure 5b: Open load: detection in ON-state, open load occurs in on-state IN t d(ST OL1 OUT ...
Page 12
Figure 7a: Overvoltage bb(over) ON(CL OUT ST Figure 9a: Overvoltage at short circuit shutdown bb(o rst) Output short to GND V OUT short circuit shutdown Overvoltage due ...
Page 13
Package and Ordering Code All dimensions in mm Standard TO-220AB/5 BTS 410 G2 TO-220AB/5, Option E3043 BTS 410 G2 E3043 Semiconductor Group Ordering code SMD TO-220AB/5, Opt. E3062 Q67060-S6104-A2 BTS410G2 E3062A T&R: Ordering code Q67060-S6104-A3 13 BTS 410 G2 Ordering ...