EP2S90F1020I4N Altera, EP2S90F1020I4N Datasheet - Page 100

• Manufacturer Part Number: EP2S90F1020I4N
• Description: IC STRATIX II FPGA 90K 1020-FBGA
• Manufacturer: Altera
• Series: Stratix® IIr

Specifications of EP2S90F1020I4N

• Number Of Logic Elements/cells: 90960
• Number Of Labs/clbs: 4548
• Total Ram Bits: 4520488
• Number Of I /o: 758
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 1020-FBGA
• Family Name: Stratix II
• Number Of Logic Blocks/elements: 90960
• # I/os (max): 758
• Frequency (max): 711.24MHz
• Process Technology: 90nm (CMOS)
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 90960
• Ram Bits: 4520488
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 1020
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-1920; EP2S90F1020I4N

I/O Structure
2–92
Stratix II Device Handbook, Volume 1
f
f
f
Differential On-Chip Termination
Stratix II devices support internal differential termination with a nominal
resistance value of 100 Ω for LVDS or HyperTransport technology input
receiver buffers. LVPECL input signals (supported on clock pins only)
require an external termination resistor. Differential on-chip termination
is supported across the full range of supported differential data rates as
shown in the DC & Switching Characteristics chapter in volume 1 of the
Stratix II Device Handbook.
For more information on differential on-chip termination, refer to the
High-Speed Differential I/O Interfaces with DPA in Stratix II & Stratix II GX
Devices chapter in volume 2 of the Stratix II Device Handbook or the
Stratix II GX Device Handbook.
For more information on tolerance specifications for differential on-chip
termination, refer to the DC & Switching Characteristics chapter in
volume 1 of the Stratix II Device Handbook.
On-Chip Series Termination Without Calibration
Stratix II devices support driver impedance matching to provide the I/O
driver with controlled output impedance that closely matches the
impedance of the transmission line. As a result, reflections can be
significantly reduced. Stratix II devices support on-chip series
termination for single-ended I/O standards with typical R
and 50 Ω. Once matching impedance is selected, current drive strength is
no longer selectable.
support on-chip series termination without calibration.
On-Chip Series Termination with Calibration
Stratix II devices support on-chip series termination with calibration in
column I/O pins in top and bottom banks. There is one calibration circuit
for the top I/O banks and one circuit for the bottom I/O banks. Each
on-chip series termination calibration circuit compares the total
impedance of each I/O buffer to the external 25- or 50-Ω resistors
connected to the RUP and RDN pins, and dynamically enables or disables
the transistors until they match. Calibration occurs at the end of device
configuration. Once the calibration circuit finds the correct impedance, it
powers down and stops changing the characteristics of the drivers.
For more information on series on-chip termination supported by
Stratix II devices, refer to the Selectable I/O Standards in Stratix II &
Stratix II GX Devices chapter in volume 2 of the Stratix II Device Handbook
or the Stratix II GX Device Handbook.
Table 2–17
shows the list of output standards that
Altera Corporation
S
values of 25
May 2007