DSPIC30F6014A-30I/PF Microchip Technology Inc., DSPIC30F6014A-30I/PF Datasheet - Page 162

• Manufacturer Part Number: DSPIC30F6014A-30I/PF
• Description: 16 BIT MCU/DSP 80LD 30MIPS 144 KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F6014A-30I/PF

• A/d Inputs: 16-Channels, 12-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 68
• Interface: CAN/I2C/SPI/UART
• Ios: 68
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 80-pin TQFP
• Programmable Memory: 144K Bytes
• Ram Size: 8K Bytes
• Timers: 5-16-bit, 2-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part

dsPIC30F6011A/6012A/6013A/6014A
20.9
The Peripheral Module Disable (PMD) registers pro-
vide a method to disable a peripheral module by stop-
ping all clock sources supplied to that module. When a
peripheral is disabled via the appropriate PMD control
bit, the peripheral is in a minimum power consumption
state. The control and status registers associated with
the peripheral will also be disabled so writes to those
registers will have no effect and read values will be
invalid.
A peripheral module will only be enabled if both the
associated bit in the PMD register is cleared and the
peripheral is supported by the specific dsPIC DSC vari-
ant. If the peripheral is present in the device, it is
enabled in the PMD register by default.
DS70143B-page 160
Note:
Peripheral Module Disable (PMD)
Registers
If a PMD bit is set, the corresponding mod-
ule is disabled after a delay of 1 instruction
cycle. Similarly, if a PMD bit is cleared, the
corresponding module is enabled after a
delay of 1 instruction cycle (assuming the
module control registers are already
configured to enable module operation).
Preliminary
20.10 In-Circuit Debugger
When MPLAB
in-circuit debugging functionality is enabled. This func-
tion allows simple debugging functions when used with
MPLAB IDE. When the device has this feature enabled,
some of the resources are not available for general
use. These resources include the first 80 bytes of data
RAM and two I/O pins.
One of four pairs of debug I/O pins may be selected by
the user using configuration options in MPLAB IDE.
These pin pairs are named EMUD/EMUC,
EMUD1/EMUC1, EMUD2/EMUC2 and MUD3/EMUC3.
In each case, the selected EMUD pin is the Emulation/
Debug Data line, and the EMUC pin is the Emulation/
Debug Clock line. These pins will interface to the
MPLAB ICD 2 module available from Microchip. The
selected pair of debug I/O pins is used by MPLAB ICD 2
to send commands and receive responses, as well as
to send and receive data. To use the in-circuit debugger
function of the device, the design must implement ICSP
connections to MCLR, V
selected EMUDx/EMUCx pin pair.
This gives rise to two possibilities:
1.
2.
If EMUD/EMUC is selected as the debug I/O pin
pair, then only a 5-pin interface is required, as
the EMUD and EMUC pin functions are multi-
plexed with the PGD and PGC pin functions in
all dsPIC30F devices.
If EMUD1/EMUC1, EMUD2/EMUC2 or EMUD3/
EMUC3 is selected as the debug I/O pin pair,
then a 7-pin interface is required, as the
EMUDx/EMUCx pin functions (x = 1, 2 or 3) are
not multiplexed with the PGD and PGC pin
functions.
®
ICD 2 is selected as a debugger, the
© 2005 Microchip Technology Inc.
DD
, V
SS
, PGC, PGD and the