ITS410E2XK Infineon Technologies, ITS410E2XK Datasheet
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
ITS410E2XK
Specifications of ITS410E2XK
Related parts for ITS410E2XK
ITS410E2XK Summary of contents
Page 1
... IN Logic ESD With external current limit (e.g. resistor R connections, reverse load current limited by connected load. Infineon Technologies AG Product Summary Overvoltage protection V Operating voltage On-state resistance Load current (ISO) Current limitation Operating temperature T protection technology. Providing embedded protective functions. Overvoltage ...
Page 2
... V is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 Load dump Infineon Technologies AG Function Logic ground Input, activates the power switch in case of logical high signal Positive power supply voltage, the tab is shorted to this pin Diagnostic feedback, low on failure ...
Page 3
... Overvoltage hysteresis 6 ) Overvoltage protection Standby current (pin Leakage output current (included Operating current (Pin =-40...+150° supply voltage increase Meassured without load See also V . Infineon Technologies AG Symbol R T =25 ° =150 ° L(ISO) I L(GNDhigh see diagram 90 OUT 10 OUT off dV /dt T =-40...+150°C ...
Page 4
... Note that the power dissipation is higher compared to normal operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature protection is not active during reverse current operation! Input and Status currents have to be limited (see max. ratings page 2 and circuit page 7). Infineon Technologies ...
Page 5
... Status invalid after positive input slope (open load) Status output (open drain) Zener limit voltage T =-40...+150° low voltage T =-40...+150° ground resistor R is used, add the voltage drop across this resistor. GND Infineon Technologies AG Symbol =-40..+150° IN(T+) T =-40..+150° IN(T 0 ...
Page 6
... L = "Low" Level X = don't care H = "High" Level Status signal after the time delay shown in the diagrams (see fig 5. page 13) Terms PROFET GND GND R GND ) Power Transistor off, high impedance Low resistance short output may be detected in ON-state by the no-load-detection bb Infineon Technologies AG Output level level ...
Page 7
... V). Short circuit detection Fault Condition: V > 8.5 V typ.; IN high ON Short circuit Logic detection unit Inductive and overvoltage output clamp V Z GND V clamped typ. ON Infineon Technologies AG Overvolt. and reverse batt. protection + ESD 6.2 V typ Open-load detection ON-state diagnostic condition: V high ...
Page 8
... OUT PROFET ST 4 GND other external inductive loads L are connected to the PROFET, additional elements like D are necessary. Infineon Technologies AG Inductive Load switch-off energy dissipation OUT 5 = Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET is OUT 5 with an approximate solution for R ...
Page 9
... Typ. transient thermal impedance chip case Z = f(t , D), D=t /T thJC [K/W] thJC 10 1 0.1 0.01 1E-5 1E-4 1E-3 1E-2 Infineon Technologies AG D= 0.5 0.2 0.1 0.05 0.02 0.01 0 1E-1 1E0 1E1 t p [s] 9 PROFET ® ITS 410 E2 2006-Mar-28 ...
Page 10
... V only if forced externally). So the device remains latched unless between turn on and t . d(SC With latch function. Reseted by a) Input low, b) Undervoltage ) No auto restart after overvoltage in case of short circuit 16 ) Low resistance short output may be detected in ON-state by the no-load-detection bb Infineon Technologies > typ bb 14 < after shutdown. In most cases ON(SC) 10 PROFET ® ITS ...
Page 11
... OUT A ST open drain A in case of too early V IN =high the device may not turn on (curve A) t approx. 150 s d(bb IN) Figure 2a: Switching a lamp OUT I L Infineon Technologies AG PROFET ® ITS 410 E2 Figure 2b: Switching an inductive load IN t d(ST OUT L(OL the time constant of load is too large, open-load-status may ...
Page 12
... OUT t d(SC d(SC) approx > 8.5 V typ. bb OUT Figure 3b: Turn on into overload L(SCp) I L(SCr) ST Heating up may require several seconds < 8.5 V typ. bb OUT Infineon Technologies AG PROFET ® ITS 410 E2 Figure 3c: Short circuit while on OUT I L **) t **) current peak approx Figure 4a: Overtemperature: Reset if T < OUT T J ...
Page 13
... Figure 5b: Open load: detection in ON-state, open load occurs in on-state IN t d(ST OL1 OUT normal open tbd s typ tbd s typ d(ST OL1) d(ST OL2) Infineon Technologies AG Figure 6a: Undervoltage OUT ST open drain t Figure 6b: Undervoltage restart of charge pump d(ST OL2) V bb(u rst) normal V ...
Page 14
... V V bb(over) ON(CL OUT ST Figure 9a: Overvoltage at short circuit shutdown bb(o rst) Output short to GND V OUT short circuit shutdown Overvoltage due to power line inductance. No overvoltage auto- restart of PROFET after short circuit shutdown. Infineon Technologies AG PROFET ® ITS 410 E2 V bb(o rst 2006-Mar-28 ...
Page 15
... Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life- support devices or systems with the express written Ordering code approval of Infineon Technologies failure of such ...