TLE7237SL Infineon Technologies, TLE7237SL Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
TLE7237SL
Manufacturer Part Number
TLE7237SL
Description
IC DRIVER SPI RELAY CTRL 24SSOP
Manufacturer
Infineon Technologies
Series
-r
Type
High Side/Low Side Driverr
Datasheet
1.TLE7237SL.pdf
(36 pages)
Specifications of TLE7237SL
Input Type
SPI
Number Of Outputs
8
On-state Resistance
900 mOhm, 1.6 Ohm
Current - Output / Channel
175mA, 380mA
Current - Peak Output
500mA, 1A
Voltage - Supply
9 V ~ 16 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
24-SSOP (0.154", 3.90mm Width)
Packages
PG-SSOP-24
Channels
8.0
Rds (on) (typ)
0.9 Ohm
Vdd
3.0 - 5.5 V
Vds(cl)
41.0 - 52.0 V
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TLE7237SL
Manufacturer:
INFINEON
Quantity:
100
Part Number:
TLE7237SL
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
CS Low to High transition:
•
•
SCLK - Serial Clock: This input pin clocks the internal shift register. The serial input (SI) transfers data into the
shift register on the falling edge of SCLK while the serial output (SO) shifts diagnostic information out on the rising
edge of the serial clock. It is essential that the SCLK pin is in low state whenever chip select CS makes any
transition.
SI - Serial Input: Serial input data bits are shifted in at this pin, the most significant bit first. SI information is read
on the falling edge of SCLK. The 8 bit input data consist of two parts (control and data). Please refer to
for further information.
SO Serial Output: Data is shifted out serially at this pin, the most significant bit first. SO is in high impedance state
until the CS pin goes to low state. New data will appear at the SO pin following the rising edge of SCLK. Please
refer to
9.2
The SPI of TLE7237SL provides daisy chain capability. In this configuration several devices are activated by the
same CS signal MCS. The SI line of one device is connected with the SO line of another device (see
which builds a chain. The ends of the chain are connected with the output and input of the master device, MO and
MI respectively. The master device provides the master clock MCLK, which is connected to the SCLK line of each
device in the chain.
Figure 10
In the SPI block of each device, there is one shift register where one bit from SI line is shifted in each SCLK. The
bit shifted out can be seen at SO. After 8 SCLK cycles, the data transfer for one device has been finished. In single
chip configuration, the CS line must go high to make the device accept the transferred data. In daisy chain
configuration the data shifted out at device #1 has been shifted in to device #2. When using three devices in daisy
chain, three times 8 bits have to be shifted through the devices. After that, the MCS line must go high (see
Figure
Data Sheet
Command decoding is only done, when after the falling edge of CS exactly a multiple (1, 2, 3, …) of eight SCLK
signals have been detected. In case of faulty transmission, the transmission error flag (TER) is set and the
command is ignored.
Data from shift register is transferred into the input matrix register.
11).
Section 9.3
MCLK
MCS
MO
Daisy Chain Capability
Daisy Chain Configuration
MI
for further information.
SI
device 1
SPI
SO
SI
27
device 2
SPI
SPI Driver for Enhanced Relay Control
SO
SI
Serial Peripheral Interface (SPI)
device 3
SPI
SPI_DasyChain.emf
Rev. 1.1, 2011-04-05
SO
TLE7237SL
Section 9.3
Figure
10),