TLE7236EM Infineon Technologies, TLE7236EM Datasheet - Page 13

• Manufacturer Part Number: TLE7236EM
• Description: IC DRIVER SPI RELAY CTRL 24SSOP
• Manufacturer: Infineon Technologies
• Series: -r
• Type: High Side/Low Side Driverr

Specifications of TLE7236EM

• Input Type: SPI
• Number Of Outputs: 8
• On-state Resistance: 900 mOhm, 1.6 Ohm
• Current - Output / Channel: 250mA, 500mA
• Current - Peak Output: 500mA, 1A
• Voltage - Supply: 9 V ~ 16 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 24-LSSOP (0.154", 3.90mm Width)
• Packages: PG-SSOP-24
• Channels: 8.0
• Rds (on) (typ): 0.9 Ohm
• Vdd: 3.0 - 5.5 V
• Vds(cl): 41.0 - 52.0 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5
The TLE7236EM is supplied by two supply voltages
feed and used by the power switches and by an integrated power supply for the register banks. The internal power
supply is designed to hold the state of the power switches including the configuration stored in the control register
bank during cranking down to 4V. There is an under voltage reset function implemented for the
which is triggered if
are reset to their default values and the device is in sleep mode (standby). Sending the SPI command
CMD.WAKE = 1 switches the device to operation mode (ON), while a command CMD.STB = 1 send the device to
sleep mode (standby) again. Please note that the device needs the time
command should be send after changing the power state via CMD.WAKE = 1 before this time is elapsed. A SPI
frame send during
The
result, the daisy chain function is available as soon as
A capacitor between pins
Please see
5.1
There is a limp home functionality implemented in the TLE7236EM, which is activated via pin LHI. Please refer to
Section 5.2
The device provides a sleep mode (stand by) to minimize current consumption, which also resets the register
banks. It is entered and left by dedicated SPI commands . The sleep mode current is minimized only when limp
home is inactive. After limp home, the device enters sleep mode automatically.
The internal power supply is designed for low voltage cranking condition down to
output channels keep their state as before configured via SPI independent of
SPI can not be used as the output and input levels refer to
the limp home mode is triggered or the
The following table shows the operation modes depending on
Operation Modes
VBB
VDD
LHI
Switches operating
Limp Home
SPI & daisy-chain
Register Banks
Diagnostic functions
5.2
The TLE7236EM offers the capability of driving dedicated channels during fail-safe operation of the system. This
limp home mode is activated by a high signal at pin LHI. In limp home mode, the SPI registers are reset and the
input pins are directly routed to the auto configuring channels (channel 4 and 5). As a result, the limp home
operation can be chosen for high-side and low-side driven loads. Due to the integrated power supply, limp home
operation is independent of digital power supply
device. After limp home operation, the device enters sleep mode in any case.
Data Sheet
V
DD
supply line is used to power the circuitry related to the SPI shift register and for driving the SO line. As a
Figure 14 “Application Diagram” on Page 35
for details.
Power Supply
Operation Modes
Limp Home Mode
t
wu(Sleep)
V
bb
is below the undervoltage threshold. After start-up of the power supply, all SPI registers
V
could be ignored.
DD
and GND is recommended (especially in case of EMI disturbances).
0 V
0 V
X
-
-
-
reset
-
V
DD
voltages comes back and therefore the SPI Interface works again.
0 V
5 V
0 V
-
-
reset
-
V
DD
. In case of stand-by, a high signal at pin LHI will wake up the
0 V
5 V
5 V
-
-
reset
-
V
V
bb
13
DD
and
is provided in the specified range independent of
V
for details.
4 V
0 V
0 V
-
-
-
DD
V
V
SPI Driver for Enhanced Relay Control
, but the device keep the current state until either
DD
bb
,
. The
V
4 V
0 V
4 V
-
reset
-
DD
and the limp home input signal LHI.
V
bb
4 V
3 V
0 V
-
-
supply line is connected to a battery
V
t
DD
wu(Sleep)
supply voltage. If
V
12 V
0 V
0 V
-
-
bb
= 4 V. During cranking, the
to initialize itself. No SPI
12 V
0 V
5 V
-
reset
-
Rev. 1.0, 2010-02-18
V
bb
TLE7236EM
Power Supply
12 V
5 V
0 V
-
power supply,
V
DD
= 0 V the
12 V
5 V
5 V
reset
-
V
bb
.