AT90USB162 Atmel Corporation, AT90USB162 Datasheet - Page 264

• Manufacturer Part Number: AT90USB162
• Manufacturer: Atmel Corporation

Specifications of AT90USB162

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 22
• Ext Interrupts: 21
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 5
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

26.3
26.4
264
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
5. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcon-
6. Values with “Power Reduction Register 1 - PRR1” disabled (0x00).
7. As specified in the USB Electrical chapter, the D+/D- pads can withstand voltages down to -1V applied through a 39Ω resis-
8. All IOs Except XTAL1, MOSI, MISO, PS2 and Reset pins
External Clock Drive Waveforms
External Clock Drive
AT90USB82/162
1.)The sum of all IOL, for ports B0-B7, C0-C7, D0-D7 should not exceed 150 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
1.)The sum of all IOL, for ports B0-B7, C0-C7, D0-D7 should not exceed 150 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
trollers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon
tor (in series with the external 22Ω resistor).
Figure 26-1. External Clock Drive Waveforms
Table 26-1.
Note:
Symbol
1/t
Δ
t
t
t
t
t
CHCX
CLCX
CLCH
CHCL
CLCL
t
CLCL
CLCL
All DC Characteristics contained in this datasheet are based on simulation and characterization of
other AVR microcontrollers manufactured in the same process technology. These values are pre-
liminary values representing design targets, and will be updated after characterization of actual
silicon.
Parameter
Oscillator
Frequency
Clock Period
High Time
Low Time
Rise Time
Fall Time
Change in period
from one clock
cycle to the next
External Clock Drive
V
IL1
V
IH1
Min.
V
125
50
50
0
CC
=2.7-5.5V
Max.
1.6
1.6
8
2
V
Min.
62.5
25
25
CC
0
=4.5-5.5V
Max.
0.5
0.5
16
2
Units
MHz
ns
ns
ns
μs
μs
%
7707F–AVR–11/10