AT90USB647 Atmel Corporation, AT90USB647 Datasheet - Page 184

• Manufacturer Part Number: AT90USB647
• Manufacturer: Atmel Corporation

Specifications of AT90USB647

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18.2.2
184
AT90USB64/128
Double Speed Operation (U2Xn)
Table 18-1
ing the UBRRn value for each mode of operation using an internally generated clock source.
Table 18-1.
Note:
Some examples of UBRRn values for some system clock frequencies are found in
page
The transfer rate can be doubled by setting the U2Xn bit in UCSRnA. Setting this bit only has
effect for the asynchronous operation. Set this bit to zero when using synchronous operation.
Setting this bit will reduce the divisor of the baud rate divider from 16 to 8, effectively doubling
the transfer rate for asynchronous communication. Note however that the Receiver will in this
case only use half the number of samples (reduced from 16 to 8) for data sampling and clock
recovery, and therefore a more accurate baud rate setting and system clock are required when
this mode is used. For the Transmitter, there are no downsides.
Operating Mode
Asynchronous Normal
mode (U2Xn = 0)
Asynchronous Double
Speed mode (U2Xn =
1)
Synchronous Master
mode
203.
BAUD
f
UBRRn
OSC
1. The baud rate is defined to be the transfer rate in bit per second (bps)
contains equations for calculating the baud rate (in bits per second) and for calculat-
Equations for Calculating Baud Rate Register Setting
Baud rate (in bits per second, bps)
System Oscillator clock frequency
Contents of the UBRRHn and UBRRLn Registers, (0-4095)
BAUD
BAUD
BAUD
Equation for Calculating
Baud Rate
=
=
=
----------------------------------------- -
16 UBRRn
-------------------------------------- -
8 UBRRn
-------------------------------------- -
2 UBRRn
(
(
(
f
f
f
OSC
OSC
OSC
(1)
+
+
+
1
1
1
)
)
)
UBRRn
UBRRn
UBRRn
Equation for Calculating
UBRR Value
=
=
=
----------------------- - 1
16BAUD
------------------- - 1
8BAUD
------------------- - 1
2BAUD
f
f
f
OSC
OSC
OSC
–
–
–
Table 18-9 on
7593K–AVR–11/09