AD7859 Analog Devices, AD7859 Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7859
Manufacturer Part Number
AD7859
Description
3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit, Parallel Sampling ADCs
Manufacturer
Analog Devices
Datasheet
1.AD7859.pdf
(28 pages)
Specifications of AD7859
Resolution (bits)
12bit
# Chan
8
Sample Rate
200kSPS
Interface
Byte,Par
Analog Input Type
SE-Bip,SE-Uni
Ain Range
(Vref) p-p,Uni (Vref)
Adc Architecture
SAR
Pkg Type
LCC,QFP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD7859AP
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7859APZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD7859APZ-REEL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD7859ASZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD7859ASZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7859ASZ-REEL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD7859BS
Manufacturer:
AD
Quantity:
1 831
Part Number:
AD7859BSZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7859LAS
Manufacturer:
ADI
Quantity:
586
Part Number:
AD7859LASZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
REV. A
Writing
With W/B at a logic high, a single write operation transfers the
full data word to the AD7859. The DB8/HBEN pin assumes its
DB8 function. Data to be written to the AD7859 should be pro-
vided on the DB0–DB15 inputs with DB0 the LSB of the data
word. With W/B at a logic low, the AD7859 requires two write
operations to transfer a full 16-bit word. DB8/HBEN assumes
its HBEN function. Data to be written to the AD7859 should
be provided on the DB0–DB7 inputs. HBEN determines
whether the byte which is to be written is high byte or low byte
data. The low byte of the data word should be written first with
DB0 the LSB of the full data word. For the high byte write,
HBEN should be high and the data on the DB0 input should be
data bit 8 of the 16-bit word with the data on DB7 the MSB of
the 16-bit word.
Figure 35 shows the write cycle timing diagram for the AD7859.
When operated in word mode, the HBEN input does not exist
and only the first write operation is required to write data to the
AD7859. Data should be provided on DB0–DB15. When oper-
ated in byte mode, the two write cycles shown in Figure 37 are
required to write the full data word to the AD7859. In Figure 37,
the first write transfers the lower 8 bits of the full data from
DB0–DB7 and the second write transfers the upper 8 bits of the
data word from DB0-DB7.
The CS and WR signals are gated internally. CS and WR may
be tied together as the timing specification for t
min. The data is latched on the rising edge of WR. The data
needs to be set up a time t
for a time t
Resetting the Parallel Interface
In the case where incorrect data is inadvertently written to the
AD7859, there is a possibility that the Test Register contents
may have been altered. If there is a suspicion that this may have
happened and the part is not operating as expected, a 16-bit
word 0000 0000 0000 0010 should be written to the AD7859 to
restore the Test Register contents to the default value.
MICROPROCESSOR INTERFACING
Interfacing the AD7859/AD7859L to a 16-Bit Data Bus
The parallel port on the AD7859 allows the device to be inter-
faced to microprocessors or DSP processors as a memory-
mapped or I/O-mapped device. The CS and RD inputs are
common to all memory peripheral interfacing. Typical inter-
faces to different processors are shown in Figures 38 to 42. In
all the interfaces shown, an external timer controls the CONVST
input of the AD7859/AD7859L, the BUSY output interrupts
the host DSP and the W/B input is logic high.
17
after the WR rising edge.
DB0 – DB7
16
before the WR rising edge and held
HBEN
WR
CS
Figure 37. Write Cycle Timing for Byte Mode Operation
*
W/B PIN LOGIC LOW
t
11
13
t
13
and t
LOW BYTE
t
15
14
t
16
is 0 ns
t
14
t
12
–25–
t
17
AD7859/AD7859L to ADSP-21xx
Figure 38 shows the AD7859/AD7859L interfaced to the
ADSP-21xx series of DSPs as a memory mapped device. A
single wait state may be necessary to interface the AD7859/
AD7859L to the ADSP-21xx depending on the clock speed of
the DSP. This wait state can be programmed via the Data
Memory Waitstate Control Register of the ADSP-21xx (please
see ADSP-2100 Family Users Manual for details). The following
instruction reads data from the AD7859/AD7859L:
where ADC is the address of the AD7859/AD7859L.
AD7859/AD7859L to TMS32020, TMS320C25 and TMS320C5x
Parallel interfaces between the AD7859/AD7859L and the
TMS32020, TMS320C25 and TMS320C5x family of DSPs are
shown in Figure 39. The memory mapped address chosen for
the AD7859/AD7859L should be chosen to fall in the I/O
memory space of the DSPs.
Figure 38. AD7859/AD7859L to ADSP-21xx Parallel
Interface
Figure 39. AD7859/AD7859L to TMS32020/C25/C5x Parallel
Interface
*ADDITIONAL PINS OMITTED FOR CLARITY
TMS32020/
TMS320C25/
TMS320C50*
t
11
*ADDITIONAL PINS OMITTED FOR CLARITY
ADSP-21xx*
A15–A0
D23–D0
HIGH BYTE
READY
STRB
R/W
MSC
INTx
A13–A0
D23–D8
IS
DMS
IRQ2
WR
RD
MR = DM(ADC)
t
12
ADDRESS BUS
ADDRESS BUS
EN
DATA BUS
EN
DATA BUS
DECODE
ADDR
DECODE
AD7859/AD7859L
ADDR
TMS320C25
ONLY
CS
WR
RD
BUSY
DB15–DB0
AD7859L*
CS
WR
RD
BUSY
DB15–DB0
AD7859/
AD7859L*
AD7859/