FAN9611 Fairchild Semiconductor, FAN9611 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
FAN9611
Manufacturer Part Number
FAN9611
Description
Manufacturer
Fairchild Semiconductor
Datasheet
1.FAN9612.pdf
(36 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
FAN9611
Manufacturer:
F
Quantity:
20 000
Company:
Part Number:
FAN9611M
Manufacturer:
FAI
Quantity:
2 500
Part Number:
FAN9611MX
Manufacturer:
FAIRCHILD/仙童
Quantity:
20 000
Part Number:
FAN9611MZD.
Manufacturer:
F
Quantity:
20 000
© 2008 Fairchild Semiconductor Corporation
FAN9611 / FAN9612 • Rev. 1.1.4
4. Analog Ground (AGND) and Power Ground
Analog ground connection (AGND) is the GND for all
control logic biased from the 5V rail. Internally, the
AGND and PGND pins are tied together by two anti-
parallel diodes to limit ground bounce difference due to
bond wire inductances during the switching actions of
the high-current gate drive circuits. It is recommended to
connect AGND and PGND pins together with a short,
low-impedance trace on the PCB (right under the IC).
PGND is the reference potential (0V) for the high-
current gate-drive circuit. Two bypass capacitors should
be connected between the VDD pin and the PGND pin.
One is the V
bias power during startup until the bootstrap power
supply comes up. The other capacitor shall be a good-
quality ceramic bypass capacitor, as close as possible
to PGND and VDD pins to filter the high peak currents
of the gate driver circuits. The value of the ceramic
bypass capacitor is a strong function of the gate charge
requirement
recommended value is between 1µF and 4.7µF to
ensure proper operation.
5. Soft-Start (SS)
Soft-start is programmed with a capacitor between the
SS pin and AGND. This is the non-inverting input of the
transconductance (g
At startup, the soft-start capacitor is quickly pre-charged
to a voltage approximately 0.5V below the voltage on
the feedback pin (FB) to minimize startup delay. Then a
5µA current source takes over and charges the soft-start
capacitor slowly, ramping up the voltage reference of
the error amplifier. By ramping up the reference slowly,
the voltage regulation loop can stay closed, actively
controlling the output voltage during startup. While the
SS capacitor is charging, the output of the error
amplifier is monitored. In case the error voltage (COMP)
ever exceeds 3.5V, indicating that the voltage loop is
close to saturation, the 5µA soft-start current is reduced.
Therefore, the soft start is automatically extended to
reduce the current needed to charge the output
capacitor, reducing the output power during startup.
This mechanism is integrated to prevent the voltage
loop from saturation. The charge current of the soft-start
capacitor can be reduced from the initial 5µA to as low
as 0.5µA minimum.
In addition to modulating the soft-start current into the
SS capacitor, the SS pin is clamped 0.2V above the FB
pin. This is useful in preventing the SS capacitor from
running away from the FB pin and defeating the closed-
loop soft-start. During the zero crossing of the input
source waveform, the input power is almost zero and
the output voltage can not be raised. Therefore the FB
(PGND)
DD
of
energy storage capacitor, which provides
the
M
) error amplifier.
power
MOSFETs
and
its
13
voltage stays flat or even decays while the SS voltage
keeps rising. This is a problem if closed-loop soft-start
should be maintained. By clamping the SS voltage to
the FB pin, this problem can be mitigated.
Furthermore, during brownout condition, the output
voltage of the converter might fall, which is reflected at
the FB pin. When FB voltage goes 0.5V below the
voltage on the SS pin, it starts discharging the soft-start
capacitor. The soft-start capacitor remains 0.5V above
the FB voltage. When the brownout condition is over,
the converter returns to normal operation gracefully,
following the slow ramp up of the soft-start capacitor at
the non-inverting input of the error amplifier.
6. Error Amplifier Compensation (COMP)
COMP pin is the output of the error amplifier. The
voltage loop is compensated by a combination of R
and C
error amplifier is between 0.195V and 4.3V. When the
COMP voltage is below about 0.195V, the PWM circuit
skips pulses. Above 4.3V, the maximum on-time limit
terminates the conduction of the boost switches.
Due to the input-voltage feedforward, the output of the
error amplifier is proportional to the input power of the
converter, independent of the input voltage. In addition,
also due to the input-voltage feedforward, the maximum
power capability of the converter and the loop gain is
independent of the input voltage. The controller’s phase-
management circuit monitors the error amplifier output
and switches to single-phase operation when the COMP
voltage falls below 0.73V and returns to two-phase
operation when the error voltage exceeds 0.93V. These
thresholds correspond to about 13% and 18% of the
maximum power capability of the design.
S
to AGND at this pin. The control range of the
Figure 19. Soft-Start Programming
www.fairchildsemi.com
S