ATA6613 ATMEL Corporation, ATA6613 Datasheet - Page 201
ATA6613
Manufacturer Part Number
ATA6613
Description
Ata6613
Manufacturer
ATMEL Corporation
Datasheet
1.ATA6613.pdf
(362 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATA6613P
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATA6613P-PLQW
Manufacturer:
ATMEL
Quantity:
5 000
Part Number:
ATA6613P-PLQW
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
- Current page: 201 of 362
- Download datasheet (6Mb)
6.17.5
6.17.5.1
9111C–AUTO–02/08
Data Transmission – The USART Transmitter
Sending Frames with 5 to 8 Data Bit
The USART Transmitter is enabled by setting the Transmit Enable (TXEN) bit in the UCSRnB
Register. When the Transmitter is enabled, the normal port operation of the TxDn pin is overrid-
den by the USART and given the function as the Transmitter’s serial output. The baud rate,
mode of operation and frame format must be set up once before doing any transmissions. If syn-
chronous operation is used, the clock on the XCKn pin will be overridden and used as
transmission clock.
A data transmission is initiated by loading the transmit buffer with the data to be transmitted. The
CPU can load the transmit buffer by writing to the UDRn I/O location. The buffered data in the
transmit buffer will be moved to the Shift Register when the Shift Register is ready to send a new
frame. The Shift Register is loaded with new data if it is in idle state (no ongoing transmission) or
immediately after the last stop bit of the previous frame is transmitted. When the Shift Register is
loaded with new data, it will transfer one complete frame at the rate given by the Baud Register,
U2Xn bit or by XCKn depending on mode of operation.
The following code examples show a simple USART transmit function based on polling of the
Data Register Empty (UDREn) Flag. When using frames with less than eight bits, the most sig-
nificant bits written to the UDRn are ignored. The USART has to be initialized before the function
can be used. For the assembly code, the data to be sent is assumed to be stored in Register
R16.
Note:
The function simply waits for the transmit buffer to be empty by checking the UDREn Flag,
before loading it with new data to be transmitted. If the Data Register Empty interrupt is utilized,
the interrupt routine writes the data into the buffer.
Assembly Code Example
C Code Example
USART_Transmit:
void USART_Transmit( unsigned char data )
{
}
; Wait for empty transmit buffer
sbis UCSRnA,UDREn
rjmp USART_Transmit
; Put data (r16) into buffer, sends the data
out
ret
/* Wait for empty transmit buffer */
while ( !( UCSRnA & (1<<UDREn)) )
/* Put data into buffer, sends the data */
UDRn = data;
1. The example code assumes that the part specific header file is included.
For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI”
instructions must be replaced with instructions that allow access to extended I/O. Typically
“LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.
UDRn,r16
;
(1)
(1)
ATA6612/ATA6613
201
Related parts for ATA6613
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Digital Attenuator, 50 Db, 6-bit, Ttl Driver, Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Voltage Variable Absorptive Attenuator, 30 Db 0.5 - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
3 Volt Voltage Variable Absorptive Attenuator 40 Db, 0.5-2.0 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenu A T O R, 15 Db, 4-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 30 Db, 4-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 28 Db, 3-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 15.5 Db, 5-bit Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
2.25 Volt Voltage Variable Absorptive Attenuator - 40 dB/ 1.8.2.5 GHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Low Current/ High Performance NPN Silicon Bipolar Transistor
Manufacturer:
Agilent(Hewlett-Packard)
Datasheet:
Part Number:
Description:
Low Current/ High Performance NPN Silicon Bipolar Transistor
Manufacturer:
Agilent(Hewlett-Packard)
Datasheet:
Part Number:
Description:
Low Current/ High Performance NPN Silicon Bipolar Transistor
Manufacturer:
Agilent(Hewlett-Packard)
Datasheet:
Part Number:
Description:
(AT-332 / AT-337) Voltage Variable Absorptive Attenuator DC - 2 GHz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 31.5 Db, 6-bit, Ttl Driver, Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
2.25 Volt Voltage Variable Absorptive Attenuator - 40 Db, 1.8.2.5 Ghz
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
Digital Attenuator, 30 Db, 4-bit, Dc - 2 Ghz
Manufacturer:
Tyco Electronics
Datasheet: