LM3S3739 Luminary Micro, Inc, LM3S3739 Datasheet - Page 65
LM3S3739
Manufacturer Part Number
LM3S3739
Description
Lm3s3739 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet
1.LM3S3739.pdf
(664 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3S3739-IQC50
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S3739-IQC50-A0
Manufacturer:
TI
Quantity:
101
Company:
Part Number:
LM3S3739-IQC50-A0
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
LM3S3739-IQC50-A0
Manufacturer:
TI/德州仪器
Quantity:
20 000
Company:
Part Number:
LM3S3739-IQC50-A0T
Manufacturer:
Texas Instruments
Quantity:
10 000
- Current page: 65 of 664
- Download datasheet (6Mb)
6.1.3
6.1.3.1
6.1.3.2
6.1.4
6.1.5
6.1.5.1
June 02, 2008
The watchdog reset timing is shown in Figure 22-13 on page 621.
Non-Maskable Interrupt
The controller has two sources of non-maskable interrupt (NMI):
■
■
If both sources of NMI are enabled, software must check that the main oscillator verification is the
cause of the interrupt in order to distinguish between the two sources.
NMI Pin
The alternate function to GPIO port pin B7 is an NMI signal. The alternate function must be enabled
in the GPIO for the signal to be used as an interrupt, as described in “General-Purpose Input/Outputs
(GPIOs)” on page 241. Note that enabling the NMI alternate function requires the use of the GPIO
lock and commit function just like the GPIO port pins associated with JTAG/SWD functionality. The
active sense of the NMI signal is High; asserting the enabled NMI signal above V
interrupt sequence.
Main Oscillator Verification Failure
The main oscillator verification circuit may generate a reset event and then, during the subsequent
POR, control is transferred to the NMI handler. The detection circuit is enabled using the CVAL bit
in the Main Oscillator Control (MOSCCTL) register. The main oscillator verification error is indicated
in the main oscillator fail status bit (MOSCFAIL bit in the Reset Cause (RESC) register. The main
oscillator verification circuit action is described in more detail in “Clock Control” on page 65.
Power Control
The Stellaris
power to the majority of the controller's internal logic. The LDO regulator provides software a
mechanism to adjust the regulated value, in small increments (VSTEP), over the range of 2.25 V
to 2.75 V (inclusive)—or 2.5 V ± 10%. The adjustment is made by changing the value of the VADJ
field in the LDO Power Control (LDOPCTL) register.
Note:
Clock Control
System control determines the control of clocks in this part.
Fundamental Clock Sources
There are four clock sources for use in the device:
■
The assertion of the NMI signal.
A main oscillator verification error.
Internal Oscillator (IOSC): The internal oscillator is an on-chip clock source. It does not require
the use of any external components. The frequency of the internal oscillator is 12 MHz ± 30%.
Applications that do not depend on accurate clock sources may use this clock source to reduce
system cost. The internal oscillator is the clock source the device uses during and following POR.
If the main oscillator is required, software must enable the main oscillator following reset and
allow the main oscillator to stabilize before changing the clock reference.
On the printed circuit board, use the LDO output as the source of VDD25 input. In addition,
the LDO requires decoupling capacitors. See “On-Chip Low Drop-Out (LDO) Regulator
Characteristics” on page 611.
®
microcontroller provides an integrated LDO regulator that may be used to provide
Preliminary
LM3S3739 Microcontroller
IH
initiates the NMI
65
Related parts for LM3S3739
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Inductor: Molded: 10u: 10%: 30M: 7.9: 440m: Axial: T/R
Manufacturer:
Inductor Supply, Inc.
Part Number:
Description:
Molded Inductor
Manufacturer:
Inductor Supply, Inc.
Datasheet:
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
Part Number:
Description:
Cree Smd Led
Manufacturer:
Cree, Inc.
Datasheet:
Part Number:
Description:
Specification For Cotco Led Lamp
Manufacturer:
Marktech Optoelectronics
Datasheet:
Part Number:
Description:
Lm3s1110 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1133 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1138 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1150 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1162 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1165 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1332 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1435 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet: