a1240a-pg132b Actel Corporation, a1240a-pg132b Datasheet - Page 10

• Manufacturer Part Number: a1240a-pg132b
• Description: Hirel Fpgas
• Manufacturer: Actel Corporation

A bs ol u t e M ax i m u m Ra t i n gs
Free air temperature range
Notes:
1.
2.
3.
4.
5.
El e c t r i c al S p ec i f i c at i o n s
Notes:
1.
2.
3.
4.
10
Symbol
V
V
V
V
I
I
C
I
I
V
V
V
I
T
Symbol
IN
OZ
CC(S)
CC(D)
IO
STG
OH
OL
IH
IL
CC
I
O
IO
1, 2
Stresses beyond those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to
absolute maximum rated conditions for extended periods may
affect device reliability. Devices should not be operated outside
the recommended operating conditions.
V
V
V
Device inputs are normally high impedance and draw extremely
low current. However, when input voltage is greater than V
0.5V or less than GND – 0.5V, the internal protection diode will be
forward biased and can draw excessive current.
Actel devices can drive and receive either CMOS or TTL signal levels. No assignment of I/Os as TTL or CMOS is required.
Tested one output at a time, V
Not tested; for information only.
V
1, 2
PP
SV
KS
OUT
= V
= V
= GND , except during device programming.
= 0V, f = 1 MHz
DC Supply Voltage
Input Voltage
Output Voltage
I/O Source Sink
Current
Storage Temperature
CC
CC
Parameter
HIGH Level Output
LOW Level Output
HIGH Level Input
LOW Level Input
Input Leakage
3-state Output Leakage
I/O Capacitance
Standby V
Dynamic V
, except during device programming.
, except during device programming.
Parameter
5
CC
CC
Supply Current V
Supply Current
3, 4
2, 3, 4
CC
= min.
–0.5 to V
–0.5 to V
–0.5 to +7.0
–65 to +150
Limits
±20
Test Condition
I
I
I
TTL Inputs
TTL Inputs
V
V
ACT 1
ACT 2/3/1200XL/3200DX
OH
OH
OL
1
O
I
I
CC
CC
= V
= V
= V
= +6 mA (CMOS)
= –4 mA (CMOS)
= –6 mA (CMOS)
+0.5
+0.5
CC
CC
CC
or GND
or GND, I
or GND
Units
mA
°C
V
V
V
CC
+
See the
O
= 0 mA
R ec o m m en d ed O pe r a t i ng C on d i t i o ns
Notes:
1.
2.
Parameter
Temperature
Range
Power Supply
Tolerance
“Power Dissipation” section on page 11.
Ambient temperature (T
industrial; case temperature (T
All power supplies must be in the recommended operating range.
For more information, refer to the Power-Up Design Considerations
application note at http://www.actel.com/appnotes.
1
Min.
3.84
–0.3
–10
–10
2.0
2
Commercial
V
CC
Max.
Commercial
0.33
+10
+10
0.8
10
3
2
+ 0.3
0 to +70
±5
A
) is used for commercial and
C
Min.
–0.3
) is used for military.
–10
–10
3.7
2.0
–55 to +125
Military
Military
±10
V
CC
Max.
+10
+10
0.4
0.8
10
20
20
+ 0.3
%V
Units
°C
Units
mA
mA
µA
µA
pF
CC
V
V
V
V
V