fxm2ic102 Fairchild Semiconductor, fxm2ic102 Datasheet
fxm2ic102
Related parts for fxm2ic102
fxm2ic102 Summary of contents
Page 1
... The FXM2IC102 is a configurable dual-voltage-supply translator designed for bi-directional voltage translation over a wide range of input and output voltages levels. The FXM2IC102 is intended for use as a voltage trans- lator in applications using the I and output voltage levels are compatible with I specification voltage levels. ...
Page 2
... OE to GND should be used to ensure that bus con- tention, excessive currents, or oscillations do not occur during power-up/power-down. The size of the pull-down resistor is based upon the current-sinking capability of the device driving the OE pin. © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 Functional Diagram ...
Page 3
... A Port Port Control Input (OE) Δt / Δv Maximum Input Edge Rate V T Free Air Operating Temperature A Note: 2. All unused inputs and I/O pins must be held at V © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 Parameter (1) < (2) Parameter = 1.65V to 5.5V CCA/B or GND. CCI 3 Rating – ...
Page 4
... Application Notes The FXM2IC102 has open-drain outputs and requires pull-up resistors on the four data I/O pins, as shown in the above figure pair of data I/O pins (A pull-down or pull-up resistors are not required. The recommended values for the pull-up resistors (R value for the bypass capacitors (C or higher and may depend upon the current-sinking capability of the device driving the OE pin. © ...
Page 5
... This is the output voltage for static conditions. Dynamic drive specifications are given in “Dynamic Output Electrical Characteristics” table. 4. “Don’t Care” indicates any valid logic level the V associated with the input side. CCI CC 6. Reflects current per supply, V © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 (V) V (V) Conditions CCA CCB 1.65–5.50 1.65–5.50 Data Inputs A n 1.65– ...
Page 6
... Dynamic output characteristics are guaranteed, but not tested the V associated with the output side. CCO CC 9. See Figure 5. 10. See Figure 6. 11. Maximum data rate is guaranteed, but not tested. © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 ( -40°C to +85° 4.5V to 5.5V 3.0V to 3.6V Typ. Max. Typ. ...
Page 7
... Symbol Parameter PLH PHL PZL PLZ (12 Port, B Port skew © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0 -40°C to +85° 4.5V to 5.5V 3.0V to 3.6V 2.3V to 2.7V Min. Max. Min. Max. Min. 1.0 4.5 1.5 5.5 2.0 1.0 4.5 1.5 5.5 1.5 2.0 6 ...
Page 8
... HIGH-to-LOW). See Figure 8. Skew guaranteed, but not tested. Capacitance Symbol Parameter C Input Capacitance Control Pin (OE Input/Output Capacitance, A I/O C Power Dissipation Capacitance PD © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0 -40°C to +85° 4.5V to 5.5V 3.0V to 3.6V 2.3V to 2.7V Min. Max. Min. Max. Min. 2.5 9.5 2.5 10.5 3.0 3 ...
Page 9
... PZL ( PLZ Load Table V CCO 1.8V ± 0.15V 2.5V ± 0.2V 3.3V ± 0.3V 5.0V ± 0.5V © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 V CCO 1k DUT 50pF 1k Input Signal Output Enable Control Data Pulses V CCA 0V LOW to HIGH Switch 0V HIGH to LOW Switch Cl 50pF 50pF 50pF 50pF Figure 1 ...
Page 10
... L + Figure 5. Active Output Rise Time and Dynamic Output Current High t period DATA CCI IN F-toggle rate period Figure 7. Maximum Data Rate (or F-toggle) in MHz © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 V CCI V OUTPUT mi GND CONTROL t pxx V CCO DATA V mo OUT = 1 ...
Page 11
... Always visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf . Package Designator Tape Section Leader (Start End) L8X Trailer (Hub End) © 2008 Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0 1.6 1.6 0. TOP VIEW 0.55 MAX ...
Page 12
... Fairchild Semiconductor Corporation FXM2IC102 Rev. 1.0.1 12 www.fairchildsemi.com ...