w77e58 Winbond Electronics Corp America, w77e58 Datasheet - Page 54
![no-image](/images/no-image-200.jpg)
w77e58
Manufacturer Part Number
w77e58
Description
8 Bit Microcontroller
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W77E58.pdf
(85 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
w77e58-24
Manufacturer:
WINBOND
Quantity:
500
Company:
Part Number:
w77e58-24
Manufacturer:
Winbond
Quantity:
600
Company:
Part Number:
w77e58-40
Manufacturer:
WINBOND
Quantity:
500
Company:
Part Number:
w77e58-40
Manufacturer:
WIN
Quantity:
226
Part Number:
w77e58-40
Manufacturer:
WIN
Quantity:
20 000
Part Number:
w77e58BP-40
Manufacturer:
WIN
Quantity:
20 000
Preliminary W77E58
When configured as a "Timer", the timer counts clock cycles. The timer clock can be programmed to
be thought of as 1/12 of the system clock or 1/4 of the system clock. In the "Counter" mode, the
register is incremented on the falling edge of the external input pin, T0 in case of Timer 0, and T1 for
Timer 1. The T0 and T1 inputs are sampled in every machine cycle at C4. If the sampled value is
high in one machine cycle and low in the next, then a valid high to low transition on the pin is
recognized and the count register is incremented. Since it takes two machine cycles to recognize a
negative transition on the pin, the maximum rate at which counting will take place is 1/24 of the
master clock frequency. In either the "Timer" or "Counter" mode, the count register will be updated at
C3. Therefore, in the "Timer" mode, the recognized negative transition on pin T0 and T1 can cause
the count register value to be updated only in the machine cycle following the one in which the
negative edge was detected.
The "Timer" or "Counter" function is selected by the " C T
/
" bit in the TMOD Special Function
Register. Each Timer/Counter has one selection bit for its own; bit 2 of TMOD selects the function for
Timer/Counter 0 and bit 6 of TMOD selects the function for Timer/Counter 1. In addition each
Timer/Counter can be set to operate in any one of four possible modes. The mode selection is done
by bits M0 and M1 in the TMOD SFR.
Time-Base Selection
The W77E58 gives the user two modes of operation for the timer. The timers can be programmed to
operate like the standard 8051 family, counting at the rate of 1/12 of the clock speed. This will ensure
that timing loops on the W77E58 and the standard 8051 can be matched. This is the default mode of
operation of the W77E58 timers. The user also has the option to count in the turbo mode, where the
timers will increment at the rate of 1/4 clock speed. This will straight-away increase the counting
speed three times. This selection is done by the T0M and T1M bits in CKCON SFR. A reset sets
these bits to 0, and the timers then operate in the standard 8051 mode. The user should set these bits
to 1 if the timers are to operate in turbo mode.
MODE 0
In Mode 0, the timer/counters act as a 8 bit counter with a 5 bit, divide by 32 pre-scale. In this mode
we have a 13 bit timer/counter. The 13 bit counter consists of 8 bits of THx and 5 lower bits of TLx.
The upper 3 bits of TLx are ignored.
The negative edge of the clock increments the count in the TLx register. When the fifth bit in TLx
moves from 1 to 0, then the count in the THx register is incremented. When the count in THx moves
from FFh to 00h, then the overflow flag TFx in TCON SFR is set. The counted input is enabled only if
TRx is set and either GATE = 0 or INTx = 1. When C T
/
is set to 0, then it will count clock cycles,
and if C T
/
is set to 1, then it will count 1 to 0 transitions on T0 (P3.4) for timer 0 and T1 (P3.5) for
timer 1. When the 13 bit count reaches 1FFFh the next count will cause it to roll-over to 0000h. The
timer overflow flag TFx of the relevant timer is set and if enabled an interrupts will occur. Note that
when used as a timer, the time-base may be either clock cycles/12 or clock cycles/4 as selected by
the bits TxM of the CKCON SFR.
- 54 -