cp3cn17 National Semiconductor Corporation, cp3cn17 Datasheet - Page 55
cp3cn17
Manufacturer Part Number
cp3cn17
Description
Reprogrammable Connectivity Processor With Can Interface
Manufacturer
National Semiconductor Corporation
Datasheet
1.CP3CN17.pdf
(220 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
cp3cn17K38
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
cp3cn17K38/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
- Current page: 55 of 220
- Download datasheet (4Mb)
11.7.3
An external reset circuit based on the LM3710 Microproces-
sor Supervisory Circuit is shown in Figure 8. It provides a
high level of fault tolerance in that it provides the ability to
monitor both the VCC supply for the core logic and the IO-
VCC supply. It also provides a low-voltage indication for the
IOVCC supply and an external watchdog timer.
The signals shown in Figure 8 are:
These additional status and feedback mechanisms allow
the CP3CN17 to recover from software hangs or perform
system shutdown functions before being placed into reset.
The standard reset threshold for the LM3710 is 3.08V with
other options for different watchdog timeout and reset time-
outs. The selection of these values are much more applica-
tion-specific. The combination of a watchdog timeout period
of 1600 ms and a reset period of 200 ms is a reasonable
starting point.
Core VCC—the 2.5V power supply rail for the core logic.
IOVCC—the 2.5–3.3V power supply rail for the I/O logic.
Watchdog Input (WDI)—this signal is asserted by the
CP3CN17 at regular intervals to indicate normal opera-
tion. A general-purpose I/O (GPIO) port may be used to
provide this signal. If the internal watchdog timer in the
CP3CN17 is used, then the LM3704 Microprocessor Su-
pervisory Circuit can provide the same features as the
LM3710 but without the watchdog timer.
RESET—an active-low reset signal to the CP3CN17.
The LM3710 is available in versions with active pullup or
an open-drain RESET output.
Power-Fail Input (PFI)—this is a voltage level derived
from the Core VCC power supply rail through a simple
resistor divider network.
Power-Fail Output (PFO)—this signal is asserted when
the voltage on PFI falls below 1.225V. PFO is connected
to the non-maskable interrupt (NMI) input on the
CP3CN17. A system shutdown routine can then be in-
voked by the NMI handler.
Low Line Output (LLO)—this signal is asserted when the
main IOVCC level fails below a warning threshold voltage
but remains above a reset detection threshold. This sig-
nal may be routed to the NMI input on the CP3CN17 or
to a separate interrupt input.
Manual
Reset
Figure 8. Fault-Tolerant External Reset
Fault-Tolerant External Reset
5-Pin Reset
LM3724
IOVCC
Circuit
SDI Reset
10k Ω
IOVCC
RESET
GND
CP3xx17
DS513
55
11.8
Table 25 lists the clock and reset registers.
11.8.1
The CRCTRL register is a byte-wide read/write register that
controls the clock selection and contains the power-on reset
status bit. At reset, the CRCTRL register is initialized as de-
scribed below:
SCLK
FCLK
PLLPWD
Reserved
7
CRCTRL
PRSFC
PRSSC
PRSAC
Name
6
CLOCK AND RESET REGISTERS
Clock and Reset Control Register (CRCTRL)
Table 25 Clock and Reset Registers
POR ACE2 ACE1 PLLPWD FCLK SCLK
The Slow Clock Select bit controls the clock
source used for the Slow Clock.
0
1
The Fast Clock Select bit selects between the
12 MHz Main Clock and the PLL as the source
used for the System Clock. After reset, the
Main Clock is selected. Attempting to switch to
the PLL while the PLLPWD bit is set (PLL is
turned off) is ignored. Attempting to switch to
the PLL also has no effect if the PLL output
clock has not stabilized.
0
1
The PLL Power-Down bit controls whether the
PLL is active or powered down (Stop PLL sig-
nal asserted). When this bit is set, the on-chip
PLL stays powered-down. Otherwise it is pow-
ered-up or it can be controlled by the Power
Management Module, respectively. Before
software can power-down the PLL in Active
mode by setting the PLLPWD bit, the FCLK bit
must be set. Attempting to set the PLLPWD
bit while the FCLK bit is clear is ignored. The
FCLK bit cannot be cleared until the PLL clock
has stabilized. After reset this bit is set.
0
1
5
–
–
–
–
–
–
Slow Clock driven by prescaled Main
Clock.
Slow Clock driven by 32.768 kHz oscilla-
tor.
The System Clock prescaler is driven by
the output of the PLL.
The System Clock prescaler is driven by
the 12-MHz Main Clock. This is the de-
fault after reset.
PLL is active.
PLL is powered down.
FF FC40h
FF FC42h
FF FC44h
FF FC46h
Address
4
3
High Frequency Clock
Low Frequency Clock
Prescaler Register
Prescaler Register
Prescaler Register
2
Clock and Reset
Control Register
Auxiliary Clock
Description
www.national.com
1
0
Related parts for cp3cn17
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: