TFA9812HN PHILIPS [NXP Semiconductors], TFA9812HN Datasheet - Page 23
TFA9812HN
Manufacturer Part Number
TFA9812HN
Description
BTL stereo Class-D audio amplifier with I2S input
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.TFA9812HN.pdf
(66 pages)
- Current page: 23 of 66
- Download datasheet (386Kb)
NXP Semiconductors
TFA9812_2
Preliminary data sheet
8.6 Class-D amplification
8.7 Protection mechanisms
The selected PWM switching frequency is 400 kHz by default and can be set to 350 kHz,
700 kHz and 750 kHz in I
this scales linearly if 32 kHz or 48 kHz is used as f
Remark: The selected sample frequency, f
frequency (f
Remark: The performance of AM radio reception can sometimes be improved by
selecting non-interfering frequencies for the PWM signal.
The Class-D power amplification of the PWM signal is carried out in two BTL power
stages. The output signal voltage level is determined by the values on the V
The power amplifiers can be explicitly put into 3-state mode by using the pin ENABLE as
shown in
Table 19.
[1]
The TFA9812 has a wide range of protection mechanisms to facilitate optimal and safe
application. All of these are active in both I
The following protections are included in the TFA9812:
The reaction of the device to the different fault conditions differs per protection.
ENABLE pin value
0
1
•
•
•
•
•
•
•
•
•
•
•
•
Can be overruled by a forced 3-state in Sleep or Fault mode.
Thermal Foldback (TF)
OverTemperature Protection (OTP)
OverCurrent Protection (OCP)
OverVoltage Protection (OVP)
UnderVoltage Protection (UVP)
Window Protection (WP)
Lock Protection (LP)
UnderFrequency Protection (UFP)
OverFrequency Protection (OFP)
Invalid BCK Protection (IBP)
DC-blocking
ESD
Table
ENABLE pin functionality
s
) in I
19. The ENABLE pin is functional in Legacy mode and in I
2
C control mode.
Rev. 02 — 22 January 2009
2
C control mode. In Legacy mode 400 kHz is the only option and
BTL stereo Class-D audio amplifier with I
2
s
C and Legacy control modes.
(selected) must be equal to the sample
Function
Output stages in 3-state mode.
Switching enabled
s
.
[1]
.
© NXP B.V. 2009. All rights reserved.
TFA9812
2
C mode.
DDP
pins.
2
S input
23 of 66
Related parts for TFA9812HN
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Tfa Th Through Hole Rf Power Attenuators
Manufacturer:
RARA Electronics Corporation
Datasheet:
Part Number:
Description:
Tfa Smd Surface Mounted Rf Power Attenuators
Manufacturer:
RARA Electronics Corporation
Datasheet:
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors