TDA9550 PHILIPS [NXP Semiconductors], TDA9550 Datasheet - Page 38
TDA9550
Manufacturer Part Number
TDA9550
Description
TV signal processor-Teletext decoder with embedded m-Controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.TDA9550.pdf
(125 pages)
- Current page: 38 of 125
- Download datasheet (521Kb)
Philips Semiconductors
Note: In the above tables the f
the 80c51 IIC module (6MHz).
I2C Port Enable
One external I
using TXT21.I2C PORT0. Any information transmitted to
the device can only be acted upon if the port is enabled.
Internal communication between the 80c51
micro-controller and the TV Signal Processor will continue
regardless of the value written to TXT21.I2C PORT0.
LED Support
Port pins P0.5 and P0.6 have a 8mA current sinking
capability to enable LEDs in series with current limiting
resistors to be driven directly, without the need for
additional buffering circuitry.
MEMORY INTERFACE
The memory interface controls the access to the
embedded DRAM, refreshing of the DRAM and page
clearing. The DRAM is shared between Data Capture,
Display and Microcontroller sections. The Data Capture
section uses the DRAM to store acquired information that
has been requested. The Display reads the DRAM
information and converts it to RGB output values. The
Microcontroller uses the DRAM as embedded auxiliary
RAM.
DATA CAPTURE
The Data Capture section takes in the analogue
Composite Video and Blanking Signal (CVBS) from One
Chip, and from this extracts the required data, which is
then decoded and stored in SFR memory.
The extraction of the data is performed in the digital
domain. The first stage is to convert the analogue CVBS
signal into a digital form. This is done using an ADC
sampling at 12MHz. The data and clock recovery is then
performed by a Multi-Rate Video Input Processor
(MulVIP). From the recovered data and clock the following
data types are extracted WST Teletext (625/525),Closed
Caption, VPS, WSS. The extracted data is stored in either
memory (DRAM) via the Memory Interface or in SFR
locations.
2000 Jun 22
Table 9 IIC Serial Rates ‘558 slow mode’
TV signal processor-Teletext decoder with
embedded -Controller
CR2
1
1
CR1
1
1
2
C port is available. This port is enabled
CR0
0
1
f
divided by
clk
(6MHz)
clk
320
240
relates to the clock rate of
I2C Bit Frequency
(KHz) at f
18.75
25
clk
38
Data Capture Features
Analogue to Digital Converter
The CVBS input is passed through a differential to single
ended converter (DIVIS), although in this device it is used
in single ended configuration with a reference.The
analogue output of DIVIS is converted into a digital
representation by a full flash ADC with a sampling rate of
12MHz.
Multi Rate Video Input Processor
The multi rate video input processor is a Digital Signal
Processor designed to extract the data and recover the
clock from the digital CVBS signal.
Video Signal Quality detector.
Data Capture for 625 line WST
Data Capture for 525 line WST
Data Capture for US Closed Caption
Data Capture for VPS data (PDC system A)
Data Capture for Wide Screen Signalling (WSS) bit
decoding
Automatic selection between 525 WST/625WST
Automatic selection between 625WST/VPS on line 16 of
VBI
Real-time capture and decoding for WST Teletext in
Hardware, to enable optimised microprocessor
throughput
Upto 10 pages stored On-Chip
Inventory of transmitted Teletext pages stored in the
Transmitted Page Table (TPT) and Subtitle Page Table
(SPT)
Automatic detection of FASTEXT transmission
Real-time packet 26 engine in Hardware for processing
accented, G2 and G3 characters
Signal quality detector for WST/VPS data types
Comprehensive Teletext language coverage
Full Field and Vertical Blanking Interval (VBI) data
capture of WST data
TDA955X/6X/8X PS/N1 series
Tentative Device Specification
Related parts for TDA9550
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors