LPC2364FB100 PHILIPS [NXP Semiconductors], LPC2364FB100 Datasheet - Page 6

• Manufacturer Part Number: LPC2364FB100
• Description: Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
Table 3.
LPC2364_66_68_1
Preliminary data sheet
Symbol
P0.5/
I2SRX_WS/
TD2/CAP2.1
P0.6/
I2SRX_SDA/
SSEL1/MAT2.0
P0.7/
I2STX_CLK/
SCK1/MAT2.1
P0.8/
I2STX_WS/
MISO1/MAT2.2
P0.9/
I2STX_SDA/
MOSI1/MAT2.3
P0.10/TXD2/
SDA2/MAT3.0
P0.11/RXD2/
SCL2/MAT3.1
P0.15/TXD1/
SCK0/SCK
P0.16/RXD1/
SSEL0/SSEL
Pin description
Pin
location
80
79
78
77
76
48
49
62
63
Type
I/O
I/O
O
I
I/O
I/O
I/O
O
I/O
I/O
I/O
O
I/O
I/O
I/O
O
I/O
I/O
I/O
O
I/O
O
I/O
O
I/O
I
I/O
O
I/O
O
I/O
I/O
I/O
I
I/O
I/O
…continued
Description
P0.5 — General purpose digital input/output pin.
I2SRX_WS — Receive Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I
TD2 — CAN2 transmitter output.
CAP2.1 — Capture input for Timer 2, channel 1.
P0.6 — General purpose digital input/output pin.
I2SRX_SDA — Receive data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I
SSEL1 — Slave Select for SSP1.
MAT2.0 — Match output for Timer 2, channel 0.
P0.7 — General purpose digital input/output pin.
I2STX_CLK — Transmit Clock. It is driven by the master and received by the slave.
Corresponds to the signal SCK in the I
SCK1 — Serial Clock for SSP1.
MAT2.1 — Match output for Timer 2, channel 1.
P0.8 — General purpose digital input/output pin.
I2STX_WS — Transmit Word Select. It is driven by the master and received by the
slave. Corresponds to the signal WS in the I
MISO1 — Master In Slave Out for SSP1.
MAT2.2 — Match output for Timer 2, channel 2.
P0.9 — General purpose digital input/output pin.
I2STX_SDA — Transmit data. It is driven by the transmitter and read by the receiver.
Corresponds to the signal SD in the I
MOSI1 — Master Out Slave In for SSP1.
MAT2.3 — Match output for Timer 2, channel 3.
P0.10 — General purpose digital input/output pin.
TXD2 — Transmitter output for UART2.
SDA2 — I
MAT3.0 — Match output for Timer 3, channel 0.
P0.11 — General purpose digital input/output pin.
RXD2 — Receiver input for UART2.
SCL2 — I
MAT3.1 — Match output for Timer 3, channel 1.
P0.15 — General purpose digital input/output pin.
TXD1 — Transmitter output for UART1.
SCK0 — Serial clock for SSP0.
SCK — Serial clock for SPI.
P0.16 — General purpose digital input/output pin.
RXD1 — Receiver input for UART1.
SSEL0 — Slave Select for SSP0.
SSEL — Slave Select for SPI.
2
2
C2 clock input/output (this is not an open drain pin).
C2 data input/output (this is not an open drain pin).
Rev. 01 — 22 September 2006
2
2
S-bus specification.
S-bus specification.
2
S-bus specification.
LPC2364/2366/2368
2
2
S-bus specification.
S-bus specification.
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Fast communication chip
6 of 48