LPC2364FB100 PHILIPS [NXP Semiconductors], LPC2364FB100 Datasheet - Page 8

• Manufacturer Part Number: LPC2364FB100
• Description: Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
• Manufacturer: PHILIPS [NXP Semiconductors]

Philips Semiconductors
Table 3.
LPC2364_66_68_1
Preliminary data sheet
Symbol
P0.26/AD0.3/
AOUT/RXD3
P0.27/SDA0
P0.28/SCL0
P0.29/U1D+
P0.30/U1D−
P1.0 to P1.31
P1.0/
ENET_TXD0
P1.1/
ENET_TXD1
P1.4/
ENET_TX_EN
P1.8/
ENET_CRS
P1.9/
ENET_RXD0
P1.10/
ENET_RXD1
P1.14/
ENET_RX_ER
P1.15/
ENET_REF_CL
K
P1.16/
ENET_MDC
P1.17/
ENET_MDIO
P1.18/
U1UP_LED/
PWM1.1/
CAP1.0
Pin description
Pin
location
6
25
24
29
30
95
94
93
92
91
90
89
88
87
86
32
Type
I/O
I
O
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I/O
O
I/O
O
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I/O
I/O
O
O
I
…continued
Description
P0.26 — General purpose digital input/output pin.
AD0.3 — ADC 0, input 3.
AOUT — DAC output.
RXD3 — Receiver input for UART3.
P0.27 — General purpose digital input/output pin.
SDA0 — I
P0.28 — General purpose digital input/output pin.
SCL0 — I
P0.29 — General purpose digital input/output pin.
U1D+ — USB1 bidirectional D+ line.
P0.30 — General purpose digital input/output pin.
U1D− — USB1 bidirectional D− line.
Port 1: Port 1 is a 32 bit I/O port with individual direction controls for each bit. The
operation of port 1 pins depends upon the pin function selected via the Pin Connect
block. Pins 2, 3, 5, 6, 7, 11, 12, and 13 of this port are not available.
P1.0 — General purpose digital input/output pin.
ENET_TXD0 — Ethernet transmit data 0.
P1.1 — General purpose digital input/output pin.
ENET_TXD1 — Ethernet transmit data 1.
P1.4 — General purpose digital input/output pin.
ENET_TX_EN — Ethernet transmit data enable.
P1.8 — General purpose digital input/output pin.
ENET_CRS — Ethernet carrier sense.
P1.9 — General purpose digital input/output pin.
ENET_RXD0 — Ethernet receive data.
P1.10 — General purpose digital input/output pin.
ENET_RXD1 — Ethernet receive data.
P1.14 — General purpose digital input/output pin.
ENET_RX_ER — Ethernet receive error.
P1.15 — General purpose digital input/output pin.
ENET_REF_CLK — Ethernet receiver clock.
P1.16 — General purpose digital input/output pin.
ENET_MDC — Ethernet MIIM clock.
P1.17 — General purpose digital input/output pin.
ENET_MDIO — Ethernet MI data input and output.
P1.18 — General purpose digital input/output pin.
U1UP_LED — USB1 GoodLink LED indicator. It is LOW when device is configured
(non-control endpoints enabled). It is HIGH when the device is not configured or during
global suspend.
PWM1.1 — Pulse Width Modulator 1, channel 1 output.
CAP1.0 — Capture input for Timer 1, channel 0.
2
2
C0 clock input/output. Open drain output (for I
C0 data input/output. Open drain output (for I
Rev. 01 — 22 September 2006
LPC2364/2366/2368
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
2
2
C compliance).
Fast communication chip
C compliance).
8 of 48