M306V5EESP Mitsubishi, M306V5EESP Datasheet - Page 109

• Manufacturer Part Number: M306V5EESP
• Description: SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
• Manufacturer: Mitsubishi

Rev. 1.0
Figure 2.11.23 Typical transmit/receive timings in UART mode
<UART0>
• Example of transmit timing when transfer data is 8 bits long (parity enabled, one stop bit)
<UART0>
• Example of transmit timing when transfer data is 9 bits long (parity disabled, two stop bits)
Transfer clock
Transmit enable
bit(TE)
Transmit buffer
empty flag(TI)
TxDi
Transmit register
empty flag (TXEPT)
Transmit interrupt
request bit (IR)
Transfer clock
Transmit enable
bit(TE)
Transmit buffer
empty flag(TI)
TxDi
Transmit register
empty flag (TXEPT)
Transmit interrupt
request bit (IR)
Shown in ( ) are bit symbols.
The above timing applies to the following settings :
Shown in ( ) are bit symbols.
• Parity is enabled.
• One stop bit.
• Transmit interrupt cause select bit = “1”.
The above timing applies to the following settings :
• Parity is disabled.
• Two stop bits.
• Transmit interrupt cause select bit = “0”.
“1”
“0”
“1”
“0”
“1”
“0”
“1”
“0”
“1”
“0”
“1”
“0”
“1”
“0”
“1”
“0”
Start
Start
ST
ST
bit
Data is set in UARTi transmit buffer register
bit
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
Cleared to “0” when interrupt request is accepted, or cleared by software
D
D
Data is set in UARTi transmit buffer register.
0
0
D
D
1
1
Tc
D
D
2
2
D
D
3
3
Tc
D
D
4
4
The transfer clock stops momentarily as CTS is “H” when the stop bit is checked.
The transfer clock starts as the transfer starts immediately CTS changes to “L”.
Transferred from UARTi transmit buffer register to UARTi transmit register
D
D
5
5
D
D
6
6
Transferred from UARTi transmit buffer register to UARTi transmit register
D
D
Tc = 16 (n + 1) / fi or 16 (n + 1) / f
Parity
7
7
bit
D
P
fi : frequency of BRGi count source (f
f
n : value set to BRGi
8
EXT
Stop
Cleared to “0” when interrupt request is accepted, or cleared by software
Tc = 16 (n + 1) / fi or 16 (n + 1) / f
bit
SP
Stop
SP
bit
: frequency of BRGi count source (external clock)
SP
fi : frequency of BRGi count source (f
f
n : value set to BRGi
EXT
Stop
ST
bit
ST
: frequency of BRGi count source (external clock)
D
D
0
0
D
D
1
1
D
D
2
2
Stopped pulsing because transmit enable bit = “0”
and ON-SCREEN DISPLAY CONTROLLER
D
D
3
3
EXT
D
D
4
MITSUBISHI MICROCOMPUTERS
4
D
D
5
EXT
5
1
M306V5ME-XXXSP
D
, f
D
6
8
6
, f
D
D
7
32
1
7
, f
)
P SP
D
8
8
, f
SPSP
32
M306V5EESP
)
ST
ST
D
0
D
D
0
1
D
1
109