TLE6228GP Infineon Technologies, TLE6228GP Datasheet

Page 1

Smart Quad Channel Low-Side Switch Features Product Summary Shorted Circuit Protection Overtemperature Protection Overvoltage Protection Parallel Control of the Inputs (PWM Applications) Seperate Diagnostic Pin for Each Channel Power - Package with integrated cooling area Standby mode ...

Page 2

VS STBY ENA IN1 ST1 IN4 ST4 IN2 ST2 IN3 ST3 V4.1 Detailed Block Diagram internal supply Overtemperature Overtemperature Channel 4 Channel 1 Open Load Overload LOGIC Open Load Overload LOGIC Overtemperature Overtemperature Channel 3 Channel 2 Open Load Overload ...

Page 3

Pin Description Pin Symbol 1 GND 2 OUT1 3 ST1 4 IN4 STBY 7 IN3 8 ST2 9 OUT2 10 GND 11 GND 12 OUT3 13 ST3 14 IN2 15 GND 16 ENA Enable Input for all ...

Page 4

Maximum Ratings for T The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the IC will result. Parameter Supply voltage Continuous drain source voltage (OUT1...OUT4) Input voltage IN1 to IN4, ...

Page 5

Electrical Characteristics Parameter and Conditions ° 150 ° (unless otherwise specified) 1. Power Supply ( Supply current (Outputs ON) Supply current (Outputs OFF) ...

Page 6

Electrical Characteristics Parameter and Conditions – 40 ° 150 ° (unless otherwise specified) 5. Standby Input (STBY) Input low voltage Input high voltage Input current 6. Diagnostic ...

Page 7

This IC is especially designed to drive inductive loads (relays, electromagnetic valves). Integrated clamp-diodes limit the output voltage when inductive loads are discharged. Four open-drain logic outputs indicate the status of the integrated ciruit. The following conditions are monitored and ...

Page 8

If current overload or overtemperature occurs for a longer time than t into an internal register and the output is shutdown. The reset is done by switching off the corresponding control input for a time longer than t Open load ...

Page 9

Note 1) : Standby is not designed for switching or PWM operation of the outputs Note 2) : overload/short-to-supply/overtemperature - events shorter than min. time t will not be latched and not reported at the status pin. Note 3) : ...

Page 10

Output Slope INL 85% 15 Overload Switch OFF Delay D(lim) I D(OL D-failure V4 ...

Page 11

Test Circuit V4 TLE 6228 GP Page 11 2010-07-10 ...

Page 12

Application Circuit V4 Page 12 2010-07-10 ...

Page 13

The blocking capacitor C is recommended to avoid critical negative voltage spikes case of bat­ tery interruption during OFF-commutation. Timing Diagrams of Diagnostic with Pulsed Input Signal Normal condition, resistive load, pulsed input signal ...

Page 14

Diagnostic status output at different open load current conditions D-failure leads to a static status signal INOFF ...

Page 15

Normal operation, followed by open load condition 12V D-failure D(OL D-failure ...

Page 16

Typical electrical Characteristics Drain-Source on-resistance 9,5V DS(ON Typical Drain- Source ON-Resistance 0,45 0,4 0,35 0,3 0,25 0,2 0,15 -50 -25 0 Typical ON Resistance versus Junction-Temperature Figure 6 : Channel ...

Page 17

Package PG - DSO - all dimensions in mm PIN KIN G A Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be ...

Page 18

Revision History Version Date Changes V3.2 V4.0: 2007-06-06: Version Change to Green Product V4.0 2007-06-06 Revision history implemented V4.0 2007-06-06 IFX Logo updated V4.0 2007-06-06 Package name according green nomenclature changed from P-DSO-20-12 to PG-DSO-20-37 V4.0 2007-06-06 Ordering Code removed ...

Page 19

... With respect to any examples or hints given herein, any typical values stated herein and/or any information regard­ ing the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. ...