M30850T3-CPE Renesas Electronics America, M30850T3-CPE Datasheet - Page 44

• Manufacturer Part Number: M30850T3-CPE
• Description: EMULATOR FOR M32C/80,84,85,86,8A
• Manufacturer: Renesas Electronics America
• Type: In Circuit Debuggerr

Specifications of M30850T3-CPE

• Contents: Compact Emulator, IDE, Assembler and Linker
• For Use With/related Products: M32C/80, M32C/84, M32C/85, M32C/86, M32C/8A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

M30850T3-CPE User’s Manual
(3) Setting SW5 on the M30850T2-EPBM board
Table 2.7 Examples of setting the switch (SW5) on the M30850T2-EPBM board
REJ10J1430-0300 Rev.3.00 Aug. 17, 2009
When not using the
analog input port
selection function
When using AN23
to AN27
When using AN20
to AN27
When using AN04
to AN07
When using AN03
to AN05 and AN25
to AN27
Analog input port
Table 2.7 lists the examples of setting the switch SW5 on the M30850T2-EPBM board.
SW5 is the switch which sets each analog input pin with the analog input port selection function.
When selecting AN00 to AN07 or AN20 to AN27 in the analog input port select bits (bit 2 and bit 1 of 0394h), set the pins
used for A/D conversion to ON, the pins not used to OFF.
AD ON 0
AD ON 0
AD ON 0
OFF 0
AD ON 0
OFF 0
OFF 0
OFF 0
AD ON 0
OFF 0
AN00 to AN02 unused: OFF
AN20 to AN22 unused: OFF
AN20 to AN22 used: OFF
AN00 to AN03 unused: OFF
AN20 to AN27 used: ON
AN23 to AN27 used: ON
AN03 to AN05 used: ON
AN25 to AN27 used: ON
AN04 to AN07 used: ON
(Factory Setting)
Setting
7
7
7
7
7
7
7
7
7
7
This is the setting when not using the analog input port selection
function. When using this product with the conditions below, set
the same as shown in the left figure.
- When using the memory expansion mode or microprocessor
- When using the multi-port sweep mode of A/D conversion
- When selecting AN0 to AN7 or AN150 to AN157 in analog
This is a setting when using the analog input port selection
function and using AN23, AN24, AN25, AN26, AN27 for analog
input pins, set the analog input pins 4, 5, 6, 7, 8 to ON as shown in
the left figure.
With this setting, set the direction registers of ports P153 to P157
to input. Pins P150 to P152 can be used for I/O port or ISTxD0,
ISCLK0, ISRxD0.
This is a setting when using the analog input port selection
function and using AN20 to AN27 for analog input pins.
Set the analog input pins 1 to 8 to ON as shown in the left figure.
With this setting, set the direction registers of ports P150 to P157
to input. Pins P150 to P157 cannot be used for I/O port or
ISTxD0, ISCLK0, ISRxD0.
This is a setting when using the analog input port selection
function and using AN04 to AN07 for analog input pins.
Set the analog input pins 5, 6, 7, 8 to ON as shown in the left
figure
With this setting, set the direction registers of ports P154 to P157
to input. Pins P150 to P153 can be used for I/O port or ISTxD0,
ISCLK0, ISRxD0.
This is a setting when using the analog input port selection
function and using AN03 to AN05 and AN25 to AN27 for analog
input pins.
Set the analog input pins 4, 5, 6, 7, 8 to ON as shown in the left
figure.
With this setting, set the direction registers of ports P153 to P157
to input. Pins P150 to P152 can be used for I/O port or ISTxD0,
ISCLK0, ISRxD0.
mode
input port select bit of A/D conversion
Description
Page 42 of 102
2. Setup