MC9S12C128CFUE Freescale Semiconductor, MC9S12C128CFUE Datasheet - Page 664

• Manufacturer Part Number: MC9S12C128CFUE
• Description: IC MCU 128K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C128CFUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 25MHz
• Interface Type: CAN/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 60
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/2.97V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: PQFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 4000 B
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 61
• Number Of Timers: 1
• Operating Supply Voltage: - 0.3 V to + 6.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Appendix A Electrical Characteristics
A.4.1.3
Provided an appropriate external reset signal is applied to the MCU, preventing the CPU from executing
code when V
the PORF bit in the CRG Flags Register has not been set.
A.4.1.4
When external reset is asserted for a time greater than PW
reset, and the CPU starts fetching the reset vector without doing a clock quality check, if there was an
oscillation before reset.
A.4.1.5
Out of STOP the controller can be woken up by an external interrupt. A clock quality check as after POR
is performed before releasing the clocks to the system.
A.4.1.6
The recovery from Pseudo STOP and Wait are essentially the same since the oscillator was not stopped in
both modes. In Pseudo Stop Mode the voltage regulator is switched to reduced performance mode to
reduce power consumption. The returning out of pseudo stop to full performance takes t
can be woken up by internal or external interrupts.After t
starts fetching the interrupt vector.
A.4.2
The device features an internal Colpitts and Pierce oscillator. The selection of Colpitts oscillator or Pierce
oscillator/external clock depends on the XCLKS signal which is sampled during reset. Pierce
oscillator/external clock mode allows the input of a square wave. Before asserting the oscillator to the
internal system clocks the quality of the oscillation is checked for each start from either power-on, STOP
or oscillator fail. t
POR or STOP if a proper oscillation is not detected. The quality check also determines the minimum
oscillator start-up time t
asserted if the frequency of the incoming clock signal is below the Assert Frequency f
664
Oscillator
DD5
SRAM Data Retention
External Reset
Stop Recovery
Pseudo Stop and Wait Recovery
is out of specification limits, the SRAM contents integrity is guaranteed if after the reset
CQOUT
UPOSC
specifies the maximum time before switching to the internal self clock mode after
. The device also features a clock monitor. A Clock Monitor Failure is
MC9S12C-Family / MC9S12GC-Family
Rev 01.24
wrs
RSTL
in Wait or t
the CRG module generates an internal
vup
+ t
wrs
in Pseudo Stop the CPU
Freescale Semiconductor
CMFA.
vup
. The controller