MC9S12E256MFUE Freescale Semiconductor, MC9S12E256MFUE Datasheet - Page 274

• Manufacturer Part Number: MC9S12E256MFUE
• Description: IC MCU 256K FLASH 25MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E256MFUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-QFP
• Processor Series: S12E
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 12
• Operating Supply Voltage: 0 V to 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• On-chip Dac: 2-ch x 8-bit
• Controller Family/series: HCS12/S12X
• No. Of I/o's: 60
• Ram Memory Size: 16KB
• Cpu Speed: 25MHz
• No. Of Timers: 3
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 8 Serial Communication Interface (SCIV3)
Enable single-wire operation by setting the LOOPS bit and the receiver source bit, RSRC, in SCI control
register 1 (SCICR1). Setting the LOOPS bit disables the path from the RXD pin to the receiver. Setting
the RSRC bit connects the TXD pin to the receiver. Both the transmitter and receiver must be enabled
(TE = 1 and RE = 1).The TXDIR bit (SCISR2[1]) determines whether the TXD pin is going to be used as
an input (TXDIR = 0) or an output (TXDIR = 1) in this mode of operation.
8.4.7
In loop operation the transmitter output goes to the receiver input. The RXD pin is disconnected from the
SCI
Enable loop operation by setting the LOOPS bit and clearing the RSRC bit in SCI control register 1
(SCICR1). Setting the LOOPS bit disables the path from the RXD pin to the receiver. Clearing the RSRC
bit connects the transmitter output to the receiver input. Both the transmitter and receiver must be enabled
(TE = 1 and RE = 1).
8.5
This section describes the interrupt originated by the SCI block.The MCU must service the interrupt
requests.
8.5.1
The SCI only originates interrupt requests. The following is a description of how the SCI makes a request
and how the MCU should acknowledge that request. The interrupt vector offset and interrupt number are
274
.
Table 8-17
Interrupts
Loop Operation
Description of Interrupt Operation
Interrupt
RDRF
TDRE
IDLE
OR
TC
lists the five interrupt sources of the SCI.
SCISR1[7]
SCISR1[6]
SCISR1[5]
SCISR1[3]
SCISR1[4]
Figure 8-25. Loop Operation (LOOPS = 1, RSRC = 0)
Source
TRANSMITTER
RECEIVER
Table 8-17. SCI Interrupt Sources
MC9S12E128 Data Sheet, Rev. 1.07
Local Enable
TCIE
RIE
ILIE
TIE
Active high level. Indicates that a byte was
transferred from SCIDRH/L to the transmit
shift register.
Active high level. Indicates that a transmit is
complete.
Active high level. The RDRF interrupt indicates
that received data is available in the SCI data
register.
Active high level. This interrupt indicates that
an overrun condition has occurred.
Active high level. Indicates that receiver input
has become idle.
RXD
TXD
Description
Freescale Semiconductor