MC908JB16JDWE Freescale Semiconductor, MC908JB16JDWE Datasheet - Page 172

• Manufacturer Part Number: MC908JB16JDWE
• Description: IC MCU 16K FLASH 6MHZ USB 20SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16JDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.2 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Universal Serial Bus Module (USB)
11.5.1.3 Address Field (ADDR)
11.5.1.4 Endpoint Field (ENDP)
11.5.1.5 Cyclic Redundancy Check (CRC)
11.5.1.6 End-of-Packet (EOP)
Technical Data
172
The address field is a 7-bit number that is used to select a particular USB
device. This field is compared to the lower seven bits of the UADDR
register to determine if a given transaction is targeting the MCU USB
device.
The endpoint field is a 4-bit number that is used to select a particular
endpoint within a USB device. For the MCU, this will be a binary number
between 0 and 2 inclusive. Any other value will cause the transaction to
be ignored.
Cyclic redundancy checks are used to verify the address and data
stream of a USB transaction. This field is five bits wide for token packets
and 16 bits wide for data packets. CRCs are generated in the transmitter
and sent on the USB data lines after both the endpoint field and the data
field.
The single-ended 0 (SE0) state is used to signal an end-of-packet
(EOP). The single-ended 0 state is indicated by both D+ and D– being
below 0.8V. EOP will be signaled by driving D+ and D– to the single-
ended 0 state for two bit times followed by driving the lines to the idle
state for one bit time. The transition from the single-ended 0 to the idle
state defines the end of the packet. The idle state is asserted for one bit
time and then both the D+ and D– output drivers are placed in their high-
impedance state. The bus termination resistors hold the bus in the idle
state.
end-of-packet transaction.
Figure 11-7
Universal Serial Bus Module (USB)
shows the data signaling and voltage levels for an
MC68HC908JB16
Freescale Semiconductor
—
Rev. 1.1