MC908JB16JDWE Freescale Semiconductor, MC908JB16JDWE Datasheet - Page 176

• Manufacturer Part Number: MC908JB16JDWE
• Description: IC MCU 16K FLASH 6MHZ USB 20SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16JDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.2 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Universal Serial Bus Module (USB)
11.5.5 Low-Speed Device
11.6 Clock Requirements
Technical Data
176
Low-speed devices are configured by the position of a pull-up resistor on
the USB D– pin of the MCU. Low-speed devices are terminated as
shown in
For low-speed transmissions, the transmitter’s EOP width must be
between 1.25µs and 1.50µs. These ranges include timing variations due
to differential buffer delay and rise/fall time mismatches and to noise and
other random effects. A low-speed receiver must accept a 670ns SE0
followed by a J transition as a valid EOP. An SE0 shorter than
330ns or an SE0 not followed by a J transition are rejected as an EOP.
Any SE0 that is 8µs or longer is automatically a reset.
The low-speed data rate is nominally 1.5 Mbps. The OSCXCLK÷2
(6MHz) signal driven by the oscillator circuits is the clock source for the
USB module and requires that a 12MHz oscillator circuit be connected
to the OSC1 and OSC2 pins. The permitted frequency tolerance for low-
speed functions is approximately
includes inaccuracies from all sources: initial frequency accuracy, crystal
capacitive loading, supply voltage on the oscillator, temperature, and
aging. The jitter in the low-speed data rate must be less than 10ns.
Figure 11-9. External Low-Speed Device Configuration
Universal Serial Bus Module (USB)
Figure 11-9
MCU
with the pull-up on the D– line.
V
D+
D–
REG
(3.3V)
±
1.5% (15,000 ppm). This tolerance
1.5 kΩ
USB LOW-SPEED CABLE
MC68HC908JB16
Freescale Semiconductor
—
Rev. 1.1