MC908JB16JDWE Freescale Semiconductor, MC908JB16JDWE Datasheet - Page 242

• Manufacturer Part Number: MC908JB16JDWE
• Description: IC MCU 16K FLASH 6MHZ USB 20SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16JDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.2 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Serial Communications Interface
12.9.5 SCI Status Register 2
Technical Data
242
Address:
SCI status register 2 contains flags to signal the following conditions:
BKF — Break Flag Bit
RPF — Reception in Progress Flag Bit
Reset:
Read:
Write:
•
•
This clearable, read-only bit is set when the SCI detects a break
character on the RxD pin. In SCS1, the FE and SCRF bits are also
set. In 9-bit character transmissions, the R8 bit in SCC3 is cleared.
BKF does not generate a CPU interrupt request. Clear BKF by
reading SCS2 with BKF set and then reading the SCDR. Once
cleared, BKF can become set again only after logic 1s again appear
on the RxD pin followed by another break character. Reset clears the
BKF bit.
This read-only bit is set when the receiver detects a logic 0 during the
RT1 time period of the start bit search. RPF does not generate an
interrupt request. RPF is reset after the receiver detects false start bits
(usually from noise or a baud rate mismatch) or when the receiver
detects an idle character. Polling RPF before disabling the SCI
module or entering stop mode can show whether a reception is in
progress.
Serial Communications Interface Module (SCI)
1 = Break character detected
0 = No break character detected
1 = Reception in progress
0 = No reception in progress
Break character detected
Incoming data
$005E
Bit 7
0
Figure 12-14. SCI Status Register 2 (SCS2)
= Unimplemented
6
0
5
0
4
0
3
0
MC68HC908JB16
Freescale Semiconductor
2
0
BKF
1
0
—
Rev. 1.1
Bit 0
RPF
0