MC9S08QG84CFFER Freescale Semiconductor, MC9S08QG84CFFER Datasheet - Page 172

• Manufacturer Part Number: MC9S08QG84CFFER
• Description: IC MCU 8BIT 8K FLASH 16-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG84CFFER

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-QFN
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 512 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Mounting Style: SMD/SMT
• Height: 1 mm
• Interface Type: I2C, SCI, SPI
• Length: 5 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.8 V
• Width: 5 mm
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Inter-Integrated Circuit (S08IICV1)
11.7
170
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
Write: IICA
— to set the slave address
Write: IICC
— to enable IIC and interrupts
Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data
Initialize RAM variables used to achieve the routine shown in
Write: IICF
— to set the IIC baud rate (example provided in this chapter)
Write: IICC
— to enable IIC and interrupts
Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data
Initialize RAM variables used to achieve the routine shown in
Write: IICC
— to enable TX
Write: IICC
— to enable MST (master mode)
Write: IICD
— with the address of the target slave. (The LSB of this byte will determine whether the communication is
The routine shown in
incoming IIC message that contains the proper address will begin IIC communication. For master operation,
communication must be initiated by writing to the IICD register.
Initialization/Application Information
IICC
IICD
IICA
IICS
IICF
master receive or transmit.)
Address to which the module will respond when addressed as a slave (in slave mode)
Data register; Write to transmit IIC data read to read IIC data
Baud rate = BUSCLK / (2 x MULT x (SCL DIVIDER))
Module configuration
Module status flags
IICEN
TCF
MULT
Figure 11-11
IICIE
IAAS
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Figure 11-10. IIC Module Quick Start
BUSY
MST
Module Initialization (Master)
Module Initialization (Slave)
can handle both master and slave IIC operations. For slave operation, an
Register Model
ARBL
Module Use
TX
ADDR
DATA
TXAK
0
ICR
Figure 11-11
Figure 11-11
RSTA
SRW
IICIF
0
RXAK
0
0
Freescale Semiconductor