Z8F6401VN020SC00TR Zilog, Z8F6401VN020SC00TR Datasheet - Page 123

• Manufacturer Part Number: Z8F6401VN020SC00TR
• Description: IC ENCORE MCU FLASH 64K 44PLCC
• Manufacturer: Zilog
• Series: Encore!®r

Specifications of Z8F6401VN020SC00TR

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-LCC (J-Lead)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: Z8F6401VN020SC00T

PS017610-0404
Error Detection
SPI Interrupts
SPI Baud Rate Generator
The SPI contains error detection logic to support SPI communication protocols and recog-
nize when communication errors have occurred. The SPI Status register indicates when a
data transmission error has been detected.
Overrun (Write Collision)
An overrun error (write collision) indicates a write to the SPI Data register was attempted
while a data transfer is in progress. An overrun sets the OVR bit in the SPI Status register
to 1. Writing a 1 to OVR clears this error flag.
Mode Fault (Multi-Master Collision)
A mode fault indicates when more than one Master is trying to communicate at the same
time (a multi-master collision). The mode fault is detected when the enabled Master’s SS
pin is asserted. A mode fault sets the COL bit in the SPI Status register to 1. Writing a 1 to
COL clears this error flag.
When SPI interrupts are enabled, the SPI generates an interrupt after data transmission.
The SPI in Master mode generates an interrupt after a character has been sent. A character
can be defined to be 1 through 8 bits by the NUMBITS field in the SPI Mode register. The
SPI in Slave mode generates an interrupt when the SS signal deasserts to indicate comple-
tion of the data transfer. Writing a 1 to the IRQ bit in the SPI Status Register clears the
pending interrupt request. If the SPI is disabled, an SPI interrupt can be generated by a
Baud Rate Generator time-out.
In SPI Master mode, the Baud Rate Generator creates a lower frequency serial clock
(SCK) for data transmission synchronization between the Master and the external Slave.
The input to the Baud Rate Generator is the system clock. The SPI Baud Rate High and
Low Byte registers combine to form a 16-bit reload value, BRG[15:0], for the SPI Baud
Rate Generator. The reload value must be greater than or equal to
(maximum baud rate is system clock frequency divided by 4). The SPI baud rate is calcu-
lated using the following equation:
When the SPI is disabled, the Baud Rate Generator can function as a basic 16-bit timer
with interrupt on time-out. To configure the Baud Rate Generator as a timer with interrupt
on time-out, complete the following procedure:
SPI Baud Rate (bits/s)
=
System Clock Frequency (Hz)
--------------------------------------------------------------------------- -
Z8F640x/Z8F480x/Z8F320x/Z8F240x/Z8F160x
2 BRG[15:0]
×
Serial Peripheral Interface
0002H
for SPI operation
Z8 Encore!
®
105