MC68HC908JL8CP Freescale Semiconductor, MC68HC908JL8CP Datasheet - Page 38

• Manufacturer Part Number: MC68HC908JL8CP
• Description: IC MCU 8K FLASH 8MHZ 28-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908JL8CP

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 23
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Memory
2.11 FLASH Block Protection
Due to the ability of the on-board charge pump to erase and program the FLASH memory in the target
application, provision is made to protect blocks of memory from unintentional erase or program operations
due to system malfunction. This protection is done by use of a FLASH block protect register (FLBPR).
The FLBPR determines the range of the FLASH memory which is to be protected. The range of the
protected area starts from a location defined by FLBPR and ends to the bottom of the FLASH memory
($FFFF). When the memory is protected, the HVEN bit cannot be set in either erase or program
operations.
In performing a program or erase operation, the FLASH block protect register must be read after setting
the PGM or ERASE bit and before asserting the HVEN bit
When the FLBPR is program with all 0’s, the entire memory is protected from being programmed and
erased. When all the bits are erased
(all 1’s), the entire memory is accessible for program and erase.
When bits within the FLBPR are programmed, they lock a block of memory, address ranges as shown in
2.12 FLASH Block Protect
erase or program of the FLBPR or the protected block of FLASH memory is prohibited. The FLBPR itself
can be erased or programmed only with an external voltage, V
also allows entry from reset into the monitor mode.
2.12 FLASH Block Protect Register
The FLASH block protect register (FLBPR) is implemented as a byte within the FLASH memory, and
therefore can only be written during a programming sequence of the FLASH memory. The value in this
register determines the starting location of the protected range within the FLASH memory.
BPR[7:0] — FLASH Block Protect Bits
38
BPR[7:0] represent bits [13:6] of a 16-bit memory address. Bits [15:14] are logic 1’s and bits [5:0] are
logic 0’s.
Non-volatile FLASH register; write by programming.
Address:
Reset:
Read:
Write:
Start address of FLASH block protect
MC68HC908JL8/JK8 • MC68HC08JL8/JK8 • MC68HC908KL8 Data Sheet, Rev. 3.1
$FFCF
BPR7
Bit 7
Figure 2-5. FLASH Block Protect Register (FLBPR)
Register. Once the FLBPR is programmed with a value other than $FF, any
BPR6
6
BPR5
5
Unaffected by reset; $FF when blank
NOTE
BPR4
1 1
4
BPR3
3
16-bit memory address
BPR[7:0]
TST
, present on the IRQ pin. This voltage
BPR2
2
BPR1
0 0 0 0 0 0
1
Freescale Semiconductor
BPR0
Bit 0