MFRC50001T/0FE,112 NXP Semiconductors, MFRC50001T/0FE,112 Datasheet - Page 6

• Manufacturer Part Number: MFRC50001T/0FE,112
• Description: IC MIFARE READER 32-SOIC
• Manufacturer: NXP Semiconductors
• Series: MIFARE®r

Specifications of MFRC50001T/0FE,112

• Rf Type: Read Only
• Frequency: 13.56MHz
• Features: ISO14443-A, ISO14443-B, ISO15693
• Package / Case: 32-SOIC (0.300", 7.50mm Width)
• Product: RFID Readers
• Operating Temperature Range: - 25 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-2222-5; 935268039112; MFRC500; MFRC51T0FED

NXP Semiconductors
Table 3.
[1]
[2]
[3]
MFRC500_33
Product data sheet
PUBLIC
Pin
12
13 to 20
21
22
23
24
25
26
27
28
29
30
31
32
[3]
[3]
[3]
Pin types: I = Input, O = Output, I/O = Input/Output, P = Power and G = Ground.
The SLRC400 uses pin name SIGOUT for pin MFOUT. The MFRC500 functionality includes test functions for the SLRC400 using pin
MFOUT.
These pins provide different functionality depending on the selected microprocessor interface type (see
detailed information).
[3]
Pin description
Symbol
DVSS
D0 to D7
AD0 to AD7
ALE
AS
nAStrb
A0
nWait
A1
A2
DVDD
AVDD
AUX
AVSS
RX
VMID
RSTPD
OSCOUT
…continued
Type
G
I/O
I/O
I
I
I
I
O
I
I
P
P
O
G
I
P
I
O
[1]
Description
digital ground
8-bit bidirectional data bus input/output on pins D0 to D7
8-bit bidirectional address and data bus input/output on pins AD0 to AD7
address latch enable input for pins AD0 to AD5; HIGH latches the internal address
address strobe input for pins AD0 to AD5; HIGH latches the internal address
not address strobe input for pins AD0 to AD5; LOW latches the internal address
address line 0 is the address register bit 0 input
address line 1 is the address register bit 1 input
address line 2 is the address register bit 2 input
digital power supply
analog power supply for pins OSCIN, OSCOUT, RX, VMID and AUX
auxiliary output is used to generate analog test signals. The output signal is
selected using the TestAnaSelect register’s TestAnaOutSel[4:0] bits
receiver input is used as the card response input. The carrier is load modulated at
13.56 MHz, drawn from the antenna circuit
internal reference voltage pin provides the internal reference voltage as a supply
Remark: It must be connected to a 100 nF block capacitor connected between pin
VMID and ground
reset and power-down input:
not wait output:
analog ground
crystal oscillator output for the oscillator’s inverting amplifier
All information provided in this document is subject to legal disclaimers.
LOW starts an access cycle
HIGH ends an access cycle
HIGH: the internal current sinks are switched off, the oscillator is inhibited and
the input pads are disconnected
LOW (negative edge): start internal reset phase
Rev. 3.3 — 15 March 2010
048033
Highly Integrated ISO/IEC 14443 A Reader IC
Section 9.1 on page 7
MFRC500
© NXP B.V. 2010. All rights reserved.
for
6 of 110