CLRC63201T/0FE,112 NXP Semiconductors, CLRC63201T/0FE,112 Datasheet - Page 98

• Manufacturer Part Number: CLRC63201T/0FE,112
• Description: IC I.CODE HS READER 32-SOIC
• Manufacturer: NXP Semiconductors
• Series: I-Coder

Specifications of CLRC63201T/0FE,112

• Rf Type: Read Only
• Frequency: 13.56MHz
• Features: ISO14443-A, ISO14443-B, ISO15693, ISO18000-3
• Package / Case: 32-SOIC (0.300", 7.50mm Width)
• Product: RFID Readers
• Operating Temperature Range: - 25 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-2199-5; 935269690112; CLRC632; CLRC63201TD

NXP Semiconductors
CLRC632_35
Product data sheet
PUBLIC
11.7.2.1 Relevant LoadKey command error flags
11.7.3 Authent1 command 0Ch
11.7.4 Authent2 command 14h
The LoadKey command interprets the first twelve bytes it finds in the FIFO buffer as the
key when stored in the correct key format as described in
page
checked and, if valid, are copied into the key buffer.
The LoadKey command can only be started by the microprocessor and it automatically
stops after copying the key from the FIFO buffer to the key buffer.
All bytes requested are copied from the FIFO buffer to the key buffer. If the key format is
not correct (see
into the key buffer and the KeyErr flag is set.
Table 157. Authent1 command 0Ch
The Authent1 command is a special Transceive command; it sends six argument bytes to
the card. The card’s response is not sent to the microprocessor, it is used instead to
authenticate the card to the CLRC632 and vice versa.
The Authent1 command can be triggered only by the microprocessor. The sequence of
states for this command are the same as those for the Transceive command; see
Section 11.2.3 on page
Table 158. Authent2 command 14h
The Authent2 command is a special Transceive command. It does not need any argument
byte, however all the data needed to be sent to the card is assembled by the CLRC632.
The card response is not sent to the microprocessor but is used to authenticate the card
to the CLRC632 and vice versa.
The Authent2 command can only be started by the microprocessor. The sequence of
states for this command are the same as those for the Transceive command; see
Section 11.2.3 on page
Command Value
Authent1
Command Value Action
Authent2
18. When the twelve argument bytes are available in the FIFO buffer they are
0Ch
14h
Section 9.2.3.1 “Key format” on page
Action
performs the first part of the Crypto1
card authentication
performs the second part of the card
authentication using the Crypto1 algorithm
Rev. 3.5 — 10 November 2009
85.
85.
Multiple protocol contactless reader IC (MIFARE/I-CODE1)
073935
Arguments and data
card Authent1 command
card block address
card serial number LSB
card serial number byte1
card serial number byte2
card serial number MSB
18) an undefined value is copied
Section 9.2.3.1 “Key format” on
Arguments
and data
-
CLRC632
© NXP B.V. 2009. All rights reserved.
Returned
data
-
Returned
data
-
-
-
-
-
-
98 of 126